502
Data
Transmission
AT command
Outline
Parameter/Explanation
Command execution example
AT
＊
DGPIR=
n
[M]
AT
＊
DRPW
[AT][M]
+++
[M]
AT+CEER
[M]
AT+CGDCONT
[M]
AT+CGEQMIN
[M]
AT+CGEQREQ
[M]
AT+CGMR
[M]
AT+CGREG=
n
[M]
[&F][&W]
AT+CGSN
[M]
AT+CLIP=
n
[AT][M]
[&F][&W]
This command is valid at
outgoing and incoming calls.
In the dial-up network setting,
you can add “186” (notified) or
“184” (not notified) to the phone
number of the access point.
(See page 490)
Displays the output power index
for receiving.
(0: Minimum value to
75: Maximum value)
Changes to the online command
state without disconnecting the
line when the escape sequence
is executed in the online mode.
Displays the reason why the
preceding call is disconnected.
Sets the APN at packet
transmission.
Registers the reference value to
decide whether the system
permits QoS (Quality of Service)
reported from the network at
establishment of PPP packet
transmission.
Sets QoS (Quality of Service) to
be requested to the network at
issuance of the PPP packet
transmission.
Displays the version of the
FOMA phone.
Sets whether the network
registration state is to be
notified.
Displays whether you are inside
or outside the service area
depending on the returned
notification.
Displays the serial number of
the FOMA phone.
Enables to display the caller’s
ID on the personal computer at
reception for 64K data
transmission or
video-phone calls.
n
=0: Uses the APN as it is. (initial value)
n
=1: Adds “184” to the APN. (always not notified.)
n
=2: Adds “186” to the APN. (always notified.)
AT
＊
DGPIR?: Displays the current setting.
−
−
<report>
Disconnection reason list (See page 506)
See page 506
AT+CGEQMIN=[parameter]
See page 506
AT+CGEQMIN=?
Lists the settable values.
AT+CGEQMIN?
Displays the current setting.
AT+CGEQREQ=[parameter]
See page 506
AT+CGEQREQ=?
Lists the settable values.
AT+CGEQREQ?
Displays the current setting.
−
n
=0: Not notified. (initial value)
n
=1: Notified at switching between the inside and
outside of the service area.
(Inquiry)
AT+CGREG?
+CGREG: <n>,<stat>
n
: Set value
stat:
0: Outside packet area
1: Inside packet area
4: Unknown
5: Inside packet area (during roaming)
−
n
=0: Does not notify. (initial value)
n
=1: Notifies.
result: +CLIP: <n>,<m>
m
=0: NW setting not to notify caller ID at calling
m
=1: NW setting to notify caller ID at calling
m
=2: Unknown
AT
＊
DGPIR=0
OK
AT
＊
DGPIR?
＊
DGPIR:0
OK
AT
＊
DRPW
＊
DRPW:0
OK
−
AT+CEER
+CEER:36
OK
See page 506
See page 506
See page 506
AT+CGMR
1234512345123456
OK
AT+CGREG=1
OK
(set to “Notified”)
AT+CGREG?
+CGREG:1,0
OK
(means the outside of the
service area)
(at moving from the outside to
the inside of the service area)
+CGREG: 1
AT+CGSN
123456789012345
OK
AT+CLIP=0
OK
AT+CLIP?
+CLIP:0, 1
OK
