Docomo FOMA P901iS, Manual

Page: 503 / 596

501
Data
Transmission
AT command Outline Parameter/Explanation Command execution example
A/
[M]
AT%V
[M]
AT&C
n
[M]
[&F][&W]
AT&D
n
[M]
[&F][&W]
AT&En
[M]
[&F][&W]
AT&F
n
[AT][M]
AT&S
n
[M]
[&F][&W]
AT&W
n
[M]
AT
＊
DANTE
[AT][M]
AT
＊ DGANSM= n
[M]
AT
＊
DGAPL= n
[,cid]
[M]
AT
＊ DGARL= n
[,cid]
[M]
Re-executes the last executed
command. No carriage return
required.
Displays the version of the
FOMA phone.
Selects operating conditions of
the circuit CD signal to the DTE.
Selects an operation to be
performed when the circuit ER
signal received from the DTE
transits between ON and OFF.
Selects the speed display for
connection.
Returns all registers to the set
values defined at shipment.
Performs line disconnection
processing if you enter this
command during transmission.
Specifies the control of the data
set ready signal to be output to
the DTE.
Stores the current set values.
Shows the number of antenna
bars. (0 to 3)
Sets rejected/accepted mode for
the packet incoming call. The
setting with this command is
valid for incoming calls in packet
transmission after you enter the
setting command.
Sets the APN of which packet
incoming call is to be accepted.
To specify the APN, use the
<cid> parameter defined in
AT+CGDCONT.
Sets the APN of which packet
incoming call is to be rejected.
To specify the APN, use the
<cid> parameter defined in
+CGDCONT.
A/
OK
AT%V
Ver1.00
OK
AT&C1
OK
AT&D1
OK
AT&E0
OK
−
AT&S0
OK
−
AT
＊
DANTE
＊
DANTE:3
OK
AT
＊
DANTE=?
＊
DANTE:(0-3)
OK
AT
＊ DGANSM=0
OK
AT
＊
DGANSM?
＊ DGANSM:0
OK
AT
＊
DGAPL=0,1
OK
AT
＊
DGAPL?
＊
DGAPL:1
OK
AT
＊
DGAPL=1
OK
AT
＊
DGAPL?
OK
AT
＊ DGARL=0,1
OK
AT
＊
DGARL?
＊ DGARL:1
OK
AT
＊
DGARL=1
OK
AT
＊
DGARL?
OK
ー
−
n =0 : CD is always ON .
n =1: CD varies depending on the carrier of the other
party’s modem. (initial value)
n =0: Ignores the ER status. (Always assumed to be
ON.)
n =1: Sets the online command state when the ER
changes from ON to OFF.
n =2: Sets the offline command state when the ER
changes from ON to OFF. (initial value)
n =0: Displays transmission speed between radio wave
blocks.
n =1: Displays DTE serial transmission speed. (Initial
value)
Only n =0 is specifiable. (can be omitted)
n =0: DR is always ON. (initial value)
n =1: DR is set to on at connection of the line (at
establishment of a transmission call).
Only n =0 is specifiable. (can be omitted)
=0: Antenna is out of the service area
=1: A single antenna
=2: Two antennas
=3: Three antennas
n =0: Invalidates the incoming call rejected/accepted
setting. (initial value)
n =1: Validates the incoming call rejected setting
(AT
＊
DGARL).
n =2: Validates the incoming call accepted setting
(AT
＊
DGAPL).
AT
＊
DGANSM?: Displays the current setting.
n =0: Adds the APN defined by <cid> to the incoming
call accepted list.
n =1: Deletes the APN defined by <cid> from the
incoming call accepted list.
Applied to all the cid contents if <cid> is omitted.
AT ＊ DGAPL?: Displays the incoming call accepted
list.
n =0: Adds the APN defined by <cid> to the incoming
call rejected list.
n =1: Deletes the APN defined by <cid> from the
incoming call rejected list.
Applied to all the cid contents if <cid> is omitted.
AT
＊
DGARL?: Displays the incoming call rejected list.
AT Command List