manualshive.com logo in svg

Avaya one-X Deskphone SIP 9620C, User Manual, Page: 99 / 170

Share
Download
Avaya one-X Deskphone SIP 9620C User Manual Download Page 99

9600 Series User Guide

Page 99

 Issue 08b (10 April 2014)

IP Office 9.0

Redirecting Calls: Twinning

14.4.2 Transferring a Call to Your Mobile

If you have been configured as a mobile twinning user, you can transfer a call to your mobile device using the features
menu.

1. Press the Features soft key if shown. To do this during a call, press the 

 PHONE key and then press the

Features soft key.

      2.If necessary, use the 

 up and down 

 arrow keys to highlight Transfer to Mobile. Press Select. 

Access Control

Your system administrator can configure whether you can access this menu option. See 

Menu Access Control

. 

14.4.3 Reclaiming a Twinned Call

When using mobile twinning, you can use the status menu to take back a call that has been redirected to and answered
at your mobile twinning destination. 

1. Press the Status soft key if shown. 

·

To access the Status menu during a call, press the 

 PHONE key and then press the Status soft key if

shown.

2. If necessary use the 

 up and down 

 arrow keys to scroll the menu to Mobile Twin Call. 

3. Press Connect. 

14.4.4 Switching Twinning Off

If you have been configured as a mobile twinning user, you can use the status menu to switch mobile twinning mode off. 

1. Press the Status soft key if shown. 

·

To access the Status menu during a call, press the 

 PHONE key and then press the Status soft key if

shown.

2. If necessary use the 

 up and down 

 arrow keys to highlight Mobile Twinning. 

·

To clear the setting, press the Off soft key. 

154

Summary of Contents for one-X Deskphone SIP 9620C











































































































































































Reviews:

No comments