manualshive.com logo in svg

Avaya one-X Deskphone SIP 9620C, User Manual, Page: 60 / 170

Share
Download
Avaya one-X Deskphone SIP 9620C User Manual Download Page 60

9600 Series User Guide

Page 60

 Issue 08b (10 April 2014)

IP Office 9.0

9.2.1 Speaker Volume

While talking handsfree via the phone's speaker, you can adjust the volume of the incoming call. The status indication
line will display a   icon followed by eight bubbles that represent the volume level.

1. With the call connected on the speaker, press the 

 key.

2. Use the 

+

 plus and 

–

 minus keys to adjust the volume.

3. The display returns to normal after a few seconds. 

9.2.2 Default Handsfree Audio Path

By default, when you make a call or answer a call without lifting the handset, the audio is played through the phone's
speaker while you speak via the phone's microphone. 

If you have a headset attached, you can change the phone's behavior so that the audio is played through the headset by
default rather than the speaker. 

1. Press the 

 MENU/HOME button and select Settings.

2. Use the 

 up and down 

 arrow keys to highlight Options & Settings. Press Select. 

3. Use the 

 up and down 

 arrow keys to highlight Call Settings. Press Select.

4. Use the 

 up and down 

 arrow keys to highlight Audio Path. 

5. Press Change to change the setting between Headset and Speaker. 

6. When completed, press the Save soft key.

7. Press the Back / Exit soft keys to exit the menus.

9.2.3 Automatic Gain Control

When using automatic gain control (AGC), the phone tries to maintain a constant audio level even if the incoming call
changes between loud and quiet. 

1. Press the 

 MENU/HOME button and select Settings.

2. Use the 

 up and down 

 arrow keys to highlight Advanced Options. Press Select. 

3. Use the 

 up and down 

 arrow keys to highlight Automatic Gain Control. Press Select. 

·

Use the 

 up and down 

 arrow keys to switch between Handset, Headset, or Speaker settings for AGC. 

·

To change the highlighted setting, press Change. 

4. When completed, press Save.

5. Press Back / Exit to exit the menus.

Summary of Contents for one-X Deskphone SIP 9620C











































































































































































Reviews:

No comments