manualshive.com logo in svg

Avaya one-X Deskphone SIP 9620C, User Manual, Page: 152 / 170

Share
Download
Avaya one-X Deskphone SIP 9620C User Manual Download Page 152

9600 Series User Guide

Page 152

 Issue 08b (10 April 2014)

IP Office 9.0

22. Menus

22.1 Features Menu

This menu is accessed by pressing the Features soft key. It can be used to access a range of user settings. 

 

To exit the whole user menu and return to the appearance menu, press the 

 PHONE/EXIT button or, if displayed,

press the Exit soft key. 

Within the menu, the 

 up and down 

 arrows keys are used to scroll through menu options. 

When the menu option displayed has sub menus, they are indicated by the ... three dots (ellipsis) icon after the menu
option name. The   left and right   arrow keys can be used to exit and enter sub-menus, except where they are being
used to change the value of a setting (see below). 

Entering a sub-menu can also be done by pressing the Select soft key or the OK button. Exiting a sub-menu can be
done by pressing the Back soft key. 

!

 The system administrator controls whether you can access various menus. Others are only available if certain

perquisites are met: 

·

While the phone is 

locked

, the Features menu cannot be accessed to change user settings. 

·

The system administrator is able to configure if you can access the Membership, State, and Fallback options of
a group. If you are not configured for any groups then the Group menu is not shown. 

84

Summary of Contents for one-X Deskphone SIP 9620C











































































































































































Reviews:

No comments