manualshive.com logo in svg

Avaya one-X Deskphone SIP 9620C, User Manual, Page: 79 / 170

Share
Download
Avaya one-X Deskphone SIP 9620C User Manual Download Page 79

9600 Series User Guide

Page 79

 Issue 08b (10 April 2014)

IP Office 9.0

Voicemail: Changing Your Voicemail Code

12.9 Switching Voicemail On/Off

You can control whether the telephone system uses voicemail to answer your unanswered calls. This does not switch off
your mailbox which you can still access to play existing messages and use other functions. 

1. Press the 

 MESSAGES button. 

·

Depending on how your system is configured, you may be required to enter your voicemail password and then
press the Done soft key. 

2. The Visual Voice menu is displayed. 

3. Use the 

 up and down 

 arrow keys to highlight Voicemail. 

4. Press the Change to switch between On or Off. 

5. Press Save to save the change. 

12.10 Transferring to Voicemail

When set to visual voice mode, the 

 key can be used to transfer your current call to the voicemail mailbox of another

user or group. 

1. With the call connected, press the 

 key. You are still connected to the call and can continue talking. 

2. Dial the extension number of the user or group to which you want to transfer the call. 

3. When the number matches a user or group, their name is displayed. 

·

To transfer the call to the user or group's mailbox, press Select. The caller will hear a few seconds of ringing
and then the mailbox greeting. 

·

To exit the transfer menu, press Cancel. 

12.11 Sending a Call to Voicemail

You can transfer a call targeted at you directly to your voicemail mailbox. 

1. If the call is not the currently highlighted call on the display, use the 

 up and down 

 arrow keys to highlight it. 

2. Press the To VM soft key. The call is redirected to your mailbox.

Summary of Contents for one-X Deskphone SIP 9620C











































































































































































Reviews:

No comments