Avaya one-X Deskphone SIP 9620C User Manual Download Page 145

Page: 145 / 170

9600 Series User Guide

Page 145

Issue 08b (10 April 2014)

IP Office 9.0

System Administration: Setting the Date

21.3 Checking the Time Server Status

For systems that automatically obtain the time from a time server, this option is available in place of the

Date

Time

and

Time Offset

functions. It allows you to check the current status of the time server and the information the

system has obtained from the time server.

1. Press the Features soft key if shown. To do this during a call, press the

PHONE key and then press the

Features soft key.

2. Use the

up and down

arrow keys to highlight Phone User. Press Select.

3. Use the

up and down

arrow keys to highlight System Administration. Press Select. If the option is not

present then you may not have been configured as a system phone user by your system administrator.

4. Enter your security PIN (login code) and press Done.

5. Use the

up and down

arrow keys to highlight Time Server Status. Press Select.

6. The time server information is listed. It includes the address of the time server, the current local time and the UTC

time. If the phone system is configured for daylight savings then the current amount of daylight savings being
applied to the local time is also shown.

144

146

Summary of Contents for one-X Deskphone SIP 9620C











































































































































































Search results

Summary of Contents for one-X Deskphone SIP 9620C

Reviews:

Avaya one-X Deskphone SIP 9620C, User Manual, Page: 145 / 170

Search results

Summary of Contents for one-X Deskphone SIP 9620C

Reviews: