manualshive.com logo in svg

Avaya one-X Deskphone SIP 9620C, User Manual, Page: 96 / 170

Share
Download
Avaya one-X Deskphone SIP 9620C User Manual Download Page 96

9600 Series User Guide

Page 96

 Issue 08b (10 April 2014)

IP Office 9.0

14.3 Do Not Disturb

·

When you are in 'do not disturb,' your callers are redirected to voicemail if available.  Otherwise, you hear a busy
tone. 

·

The only people who can call you are those calling from numbers in your 'do not disturb' exceptions list.
Forwarding can still be applied to these calls. 

·

Calls to any hunt group of which you are a member are not presented to you (unless you are the last available
member of the group). 

·

Enabling 'do not disturb' will not affect any calls already being presented to your phone. 

·

You can still use the phone to make outgoing calls. When you go off-hook you will hear broken dial tone. 

·

N = No Calls (Do Not Disturb) 
An N is shown after your extension name on the phone's idle display when you have 'do not disturb' enabled. 

Default Short Codes

Short codes are numbers that you can dial to enable and disable various features. The following are default short codes
that may be available. However, your system administrator can remove and change the short codes available to you or
all users. 

·

Switch Do Not Disturb On: *08 
Set your phone to 'do not disturb.' 

·

Switch Do Not Disturb Off: *09 
Switch off 'do not disturb.' 

·

Add a Do Not Disturb Exception Number: *10*N# 
Add a number (N) to your list of 'do not disturb' exceptions. 

·

Delete a Do Not Disturb Exception Number: *11*N# 
Remove a number (N) from your list of 'do not disturb' exceptions. 

·

Cancel All Forwarding: *00 
Switch off any forwarding (includes 'forward unconditional,' 'forward on busy,' 'forward on no answer,' 'follow me,'
and 'do not disturb').

Summary of Contents for one-X Deskphone SIP 9620C











































































































































































Reviews:

No comments