manualshive.com logo in svg

Avaya one-X Deskphone SIP 9620C, User Manual, Page: 20 / 170

Share
Download
Avaya one-X Deskphone SIP 9620C User Manual Download Page 20

9600 Series User Guide

Page 20

 Issue 08b (10 April 2014)

IP Office 9.0

1.10 Button Modules

The addition of a button module allows the phone to support additional programmable buttons. 

·

Do not connect or disconnect a button module yourself. Your system administrator will arrange this if necessary.
Failure to connect and restart the equipment in the correct order may cause the phone and or the button module
to function incorrectly. 

9608 and 9641 Phones

These phones support BM12 button modules. Each button module provides the phone with an additional 24 buttons (2
pages of 12) which can be used as 

appearance buttons

 and or 

feature buttons

. For IP Office Release 9.0, these

phone can also support SBM24 modules instead (see below) but not a mix of different module types. 

Up to three button modules can be attached to each phone. However the number of button modules supported by the
telephone system may be limited by the total number of button modules attached to other phones on the telephone
system. 

9630, 9640, and 9650 Phones

All variants of these phones support SBM24 button modules. Each button module provides the phone with an additional
24 buttons which can be used as 

appearance buttons

 and or 

feature buttons

. 

Up to three button modules can be attached to each phone. However the number of button modules supported by the
telephone system may be limited by the total number of button modules attached to other phones on the telephone
system. 

9620 Phones and 9621 Phones

These phones do not support any additional button modules.

158

108

158

108

Summary of Contents for one-X Deskphone SIP 9620C











































































































































































Reviews:

No comments