manualshive.com logo in svg

Avaya one-X Deskphone SIP 9620C, User Manual, Page: 33 / 170

Share
Download
Avaya one-X Deskphone SIP 9620C User Manual Download Page 33

9600 Series User Guide

Page 33

 Issue 08b (10 April 2014)

IP Office 9.0

Answering Calls:  

3.1 Diverting a Call to Voicemail

You can transfer a call targeted at you directly to your voicemail mailbox. 

1. If the call is not the currently highlighted call on the display, use the 

 up and down 

 arrow keys to highlight it. 

2. Press the To VM soft key. The call is redirected to your mailbox.

3.2 Ignoring an Incoming Call

You can quiet the ringer of a currently alerting call. The call will continue alerting visually but with no audible ring. 

1. If the call is not the currently highlighted call on the display, use the 

 up and down 

 arrow keys to highlight it. 

2. Press the Ignore soft key. 

3. The call will continue alerting but with no audible ring. 

3.3 Answering a Page Call

Your phone can be paged if you have no other connected call in progress. The page is heard through the phone's
speaker. This will only happen if your phone is currently idle. 

A call connected automatically after a single beep is a page call directly to you or to a group of which your phone is a
member. You can hear the caller but they cannot hear you.

·

A page call is indicated in the display by the word Page. 

·

To answer the page call, press the Answer soft key. The call is turned into a normal call. You can continue
handsfree or pickup the handset. 

·

To ignore the page call, press the Drop soft key. 

Summary of Contents for one-X Deskphone SIP 9620C











































































































































































Reviews:

No comments