manualshive.com logo in svg

Avaya one-X Deskphone SIP 9620C, User Manual, Page: 53 / 170

Share
Download
Avaya one-X Deskphone SIP 9620C User Manual Download Page 53

9600 Series User Guide

Page 53

 Issue 08b (10 April 2014)

IP Office 9.0

Conference Calls: Dropping/Muting Parties

8.4 Dropping/Muting Parties

You can drop parties from a conference call, including yourself. You can also mute other parties. 

1. While connected to a conference call, if you press the Details key, the conference details menu is displayed. 

2. You can then perform the following actions: 

·

To scroll through the list of callers in the conference, use the 

 up and down 

 arrow keys.

·

To drop a caller from the conference, highlight them and press Drop. 

·

To mute a caller, highlight them and press Mute. Repeat this to unmute them. 

·

To return to the call display, press the Back soft key. 

Note: If you are the only internal user in the conference, depending on your telephone system's configuration, dropping
yourself might end the conference. Consult your system administrator for details. 

8.5 Holding a Conference Call

Using the Hold soft key you can put a conference call on hold in the same way as you can for a normal call. The
appearance key for the conference call will show a fast-flashing red lamp. 

To take the conference call off hold, press the appearance key. 

Important - Holding Conference Calls

You can hold a conference call in the same way as holding a normal call. Holding the conference call does not affect the
other conference parties who can continue talking. You will also still be listed as a member of the conference call in the
conference details. 

Warning: This only applies to conference calls hosted by your own telephone system. Holding your call to a conference
hosted on another telephone system may cause that conference to hear your system's music on hold.  

Summary of Contents for one-X Deskphone SIP 9620C











































































































































































Reviews:

No comments