manualshive.com logo in svg

Avaya one-X Deskphone SIP 9620C, User Manual, Page: 92 / 170

Share
Download
Avaya one-X Deskphone SIP 9620C User Manual Download Page 92

9600 Series User Guide

Page 92

 Issue 08b (10 April 2014)

IP Office 9.0

Default Short Codes

Short codes are numbers that you can dial to enable and disable various features. The following are default short codes
that may be available. However, your system administrator can remove and change the short codes available to you or
all users. 

·

Cancel All Forwarding: *00 
Switch off any forwarding (includes 'forward unconditional,' 'forward on busy,' 'forward on no answer,' 'follow me,'
and 'do not disturb').

·

Set the Forward Unconditional Destination: *07*N# 
Set the destination number (N) for 'forward unconditional' when it is switched on. 

·

Switch Forward Unconditional On: *01 
Switch on 'forward unconditional.' A destination must have been set. 

·

Switch Forward Unconditional Off: *02 

·

Include Hunt Group Calls in Forward Unconditional: *50 

·

Exclude Hunt Group Calls from Forward Unconditional: *51 

·

Set the Forward On Busy/No Answer Destination: *57*N# 
Set the destination number (N) for 'forward on busy' and 'forward on no answer.' If no number has been set,
those functions will use the 'forward unconditional' number if set. 

·

Switch Forward On Busy On: *03 

·

Switch Forward On Busy Off: *04 

·

Switch Forward on No Answer On: *05 

·

Switch Forward on No Answer Off: *06 

Summary of Contents for one-X Deskphone SIP 9620C











































































































































































Reviews:

No comments