Avaya one-X Deskphone SIP 9620C User Manual Download Page 77

Page: 77 / 170

9600 Series User Guide

Page 77

Issue 08b (10 April 2014)

IP Office 9.0

Voicemail: Mailbox Greeting

12.6 Mailbox Greeting

While the voicemail system will play a generic greeting to a caller, prompting them to leave a message, you can record
your own greeting.

1. Press the

MESSAGES button.

Depending on how your system is configured, you may be required to enter your voicemail password and then
press the Done soft key.

2. The Visual Voice menu is displayed.

3. Use the

up and down

arrow keys to scroll to the Greeting option and press Select.

4. Use the soft keys to listen to and record your mailbox greeting.

Record
Record a new greeting. Note that the greeting must be at least three seconds long or the voicemail system
will discard it.

Listen
Listen to the current greeting or the new greeting just recorded.

Submit
Submit the new recording as your mailbox greeting.

More
Switch between the different sets of available soft key functions.

Delete
Delete your current mailbox greeting. The greeting will return to its default mailbox greeting.

Cancel
Return to the main Visual Voice menu.

Summary of Contents for one-X Deskphone SIP 9620C











































































































































































Search results

Summary of Contents for one-X Deskphone SIP 9620C

Reviews:

Avaya one-X Deskphone SIP 9620C, User Manual, Page: 77 / 170

Search results

Summary of Contents for one-X Deskphone SIP 9620C

Reviews: