manualshive.com logo in svg

Avaya one-X Deskphone SIP 9620C, User Manual, Page: 137 / 170

Share
Download
Avaya one-X Deskphone SIP 9620C User Manual Download Page 137

9600 Series User Guide

Page 137

 Issue 08b (10 April 2014)

IP Office 9.0

Status Menu: Group Membership

19.8 Group Membership

Your system administrator can grant you the ability to enable/disable your membership to a group through the Status
menu. When your membership to a group is disabled, you do not receive group calls for that group. 

1. Press the Status soft key if shown. 

·

To access the Status menu during a call, press the 

 PHONE key and then press the Status soft key if

shown.

2. Use the 

 up and down 

 arrow keys to highlight the hunt group name and your current membership status (

Enabled or Disabled). 

3. Press the Enable or Disable soft key to change the status of your membership to that group. 

4. Press Exit.

19.9 Group Service Status

If the system administrator has allowed you, you can change the service state of a group through the Status menu. 

1. Press the Status soft key if shown. 

·

To access the Status menu during a call, press the 

 PHONE key and then press the Status soft key if

shown.

2. Use the 

 up and down 

 arrow keys to highlight the hunt group name and your current membership status. 

3. Select the required state using the soft keys: 

·

In Service 
The groups operates as normal, distributing calls to available members of the group. 

·

Night Service 
The group is in 'night service' mode. Calls are redirected to its night service fallback group 

if set

, otherwise

to voicemail if available. 

·

A hunt group can also be put into and out of night service automatically by the telephone system using a
time profile. If that is the case, the night service state cannot be overridden using manual controls. 

·

Out of Service 
The group is out of service. Calls are redirected to its out of service fallback group 

if set

, otherwise to

voicemail if available. 

·

!

 The system administrator is able to configure whether you have access to the Membership, State and

Fallback options of a group. If you are not configured for any groups then the Group menu is not shown. 

19.10 Mobile Twinning

If you have been configured as a mobile twinning user, you can use the status menu to switch mobile twinning mode off. 

1. Press the Status soft key if shown. 

·

To access the Status menu during a call, press the 

 PHONE key and then press the Status soft key if

shown.

2. If necessary use the 

 up and down 

 arrow keys to highlight Mobile Twinning. 

·

To clear the setting, press the Off soft key. 

106

106

Summary of Contents for one-X Deskphone SIP 9620C











































































































































































Reviews:

No comments