manualshive.com logo in svg

Avaya one-X Deskphone SIP 9620C, User Manual, Page: 147 / 170

Share
Download
Avaya one-X Deskphone SIP 9620C User Manual Download Page 147

9600 Series User Guide

Page 147

 Issue 08b (10 April 2014)

IP Office 9.0

System Administration: Setting the Time Offset

21.6 Shutting Down the System

You can shutdown the telephone system for a specified number of minutes. Note that this is not a polite shut-down, once
you have confirmed the action, any existing calls and services using the telephone system will start being disconnected.
The telephone system will then remain unavailable for the duration you specify, the default being 10 minutes. After the
shutdown duration it will take up to 5 more minutes for the telephone system to complete its restart. 

!

 WARNINGS

·

A shutdown must always be used to switch off the system. Simply removing the power cord or switching off the
power input may cause errors. 

·

This is not a polite shutdown, any users calls and services in operation will be stopped. Once shutdown, the
system cannot be used to make or receive any calls until restarted. 

·

The shutdown process takes up to a minute to complete. When shutdown, the CPU LED and the base card LEDs 1
and 9 (if trunk daughter card fitted) will flash red rapidly. The memory card LEDs are extinguished. Do not remove
power from the system or remove any of the memory cards until the system is in this state.

·

To restart a system when shutdown indefinitely, or to restart a system before the timed restart, switch power to
the system off and on again. 

1. Press the Features soft key if shown. To do this during a call, press the 

 PHONE key and then press the

Features soft key.

2. Use the 

 up and down 

 arrow keys to highlight Phone User. Press Select.  

3. Use the 

 up and down 

 arrow keys to highlight System Administration. Press Select. If the option is not

present then you may not have been configured as a system phone user by your system administrator. 

4. Enter your security PIN (login code) and press Done. 

5. Use the 

 up and down 

 arrow keys to highlight System Shutdown. Press Select. 

6. The current default timeout (10 minutes) setting is shown and can be used by pressing OK soft key. Otherwise,

enter the timeout required in hours and minutes and then press the Ok soft key.

·

The allowable range for the timeout is from 00:00 to 24:00. Note that a timeout of 00:00 indicates infinite
(no) timeout.

·

The Ok soft key is not displayed if the timeout entered is not within the allowed range. 

·

To enter the : symbol in the timeout press either the * or # key. 

·

To delete the previous digit or character entered press the   left arrow key. 

7. After pressing the Ok soft key, you will be asked to confirm whether you want to shutdown the telephone system.

Only proceed if you are sure. If you are not sure press Back. 

8. If you press the Confirm soft key, the telephone system will switch itself to a shutdown state. This will disconnect

all current calls and services. 

Summary of Contents for one-X Deskphone SIP 9620C











































































































































































Reviews:

No comments