manualshive.com logo in svg

Avaya one-X Deskphone SIP 9620C, User Manual, Page: 141 / 170

Share
Download
Avaya one-X Deskphone SIP 9620C User Manual Download Page 141

9600 Series User Guide

Page 141

 Issue 08b (10 April 2014)

IP Office 9.0

Short Codes:  

Forwarding

·

Cancel All Forwarding: *00 
Switch off any forwarding (includes 'forward unconditional,' 'forward on busy,' 'forward on no answer,' 'follow me,'
and 'do not disturb').

·

Set the Forward Unconditional Destination: *07*N# 
Set the destination number (N) for 'forward unconditional' when it is switched on. 

·

Switch Forward Unconditional On: *01 
Switch on 'forward unconditional.' A destination must have been set. 

·

Switch Forward Unconditional Off: *02 

·

Include Hunt Group Calls in Forward Unconditional: *50 

·

Exclude Hunt Group Calls from Forward Unconditional: *51 

·

Set the Forward On Busy/No Answer Destination: *57*N# 
Set the destination number (N) for 'forward on busy' and 'forward on no answer.' If no number has been set,
those functions will use the 'forward unconditional' number if set. 

·

Switch Forward On Busy On: *03 

·

Switch Forward On Busy Off: *04 

·

Switch Forward on No Answer On: *05 

·

Switch Forward on No Answer Off: *06 

Hunt Group

·

Night Service Status On: *20*N# 
Set a hunt group into night service status by entering its extension number (N).

·

Night Service Status Off: *21*N# 
Take a hunt group out of night service status by entering its extension number (N). 

Login

·

Log In: *35*N*P# 
Log in to a phone using your extension number (N) and login code (P). 

·

Log Out: *36 
Log yourself out from the phone where you are currently logged in. 

Voicemail

·

Check Messages: *17 
Access mailboxes to check for messages. 

·

Voicemail On: *18 
Allow voicemail to be used to answer calls. 

·

Voicemail Off: *19 
Stop voicemail being used to answer calls. 

·

Voicemail Ringback On: *48 
Have voicemail ring your phone when you have any new messages. It will call when you use the phone.

·

Voicemail Ringback Off: *49 
Switch off ringback. 

Summary of Contents for one-X Deskphone SIP 9620C











































































































































































Reviews:

No comments