4.12 IP Camera connections
You can connect IP cameras to your multifunction
display.
Note:
Compatible IP cameras must be able to be
configured to:
• automatically assign an IP address via DHCP
prior to connecting to your multifunction display
or network.
• allow unauthenticated, anonymous ONVIF
access.
Please refer to the instructions supplied with your
IP camera for configuration details.
Note:
Your multifunction display must be powered
up before power is applied to any networked
IP cameras, this is to enable your multifunction
display to assign the IP camera(s) a valid IP
address.
IP camera(s) can be connected directly to a network
connector on your multifunction display.
D12900-2
3
2
1
4
Item
Description
1
Multifunction display rear connector panel
2
CAM200IP
3
RayNet to RJ45 adaptor cable (A62360 / A80151
/ A80159)
4
Ethernet coupler (R32142)
Note:
The gS Series multifunction displays can provide
Power over Ethernet (PoE) to compatible IP
cameras.
Refer to the
Power over Ethernet (PoE)
section for
details on PoE assignment.
You can also connect multiple IP cameras via the
SeaTalk
hs
network
D12901-2
1
2
4
4
4
4
5
5
5
5
3
Item
Description
1
Multifunction display
2
Network switch
3
RayNet to RJ45 adaptor cables (A62360 /
A80151 / A80159)
4
CAM200IP
s
5
Ethernet couplers (R32142)
Note:
Network switches do not provide PoE,
connected cameras must have their own power
supply.
Tip
If your IP camera(s) are not detected by your
multifunction display, try power cycling the IP
camera(s) whilst leaving your multifunction display
powered up.
IP camera guidance
Raymarine
®
MFD
s are capable of displaying IP
camera feeds. Whilst third-party IP cameras may
work,
Raymarine
®
highly recommends only using
Raymarine
®
IP cameras such as the
CAM200IP
.
As guidance any third-party IP camera must conform
to the following:
• The camera must support H.264 compression and
RTSP (Real time Streaming Protocol).
• The camera must be ONVIF compliant
• The camera must be capable of and be setup to
allow unauthenticated anonymous access
• The camera must be capable of and be setup to
assign an IP address automatically via DHCP
• The camera resolution must be set to no higher
than 720p
The camera settings must be checked and if
necessary adjusted using a PC and the software
supplied with the camera, prior to adding the camera
to the
SeaTalk
hs
network.
Important: Raymarine
®
does not guarantee
compatibility with third-party IP cameras.
60
gS Series
Содержание Raymarine gS 195
