FUTABA 01000141 Скачать руководство пользователя страница 76

Страница: 76 / 225

System type

■ FASSTest 18CH ---

■ FASSTest 12CH ---

■ FASST MULTI ---

■ FASST 7CH --- FASST-7CH system receiver mode. Up to 7 channels can be used.
■ T-FHSS Air ---

■ S-FHSS --- S-FHSS system receiver mode. Up to 8 channels can be used.

FASSTest system receiver mode. Applicable with the telemetry sensor unit. Up

to 18 channels (lON/OFF2) can be used.

T-FHSS system receiver mode. Applicable with the telemetry sensor unit. Up to

18 channels (lON/OFF2) can be used.

FASSTest system receiver mode. Applicable with receiver voltage display. Up to

12 channels (lON/OFF2) can be used. Telemetry Sensor cannot be used,

but the response speed is faster than that of the 18CH mode.

FASST-MULTI system receiver mode. Up to 18 channels (lON/OFF2)

can be used.

•

Analog servos cannot be used with the R7108SB in the FASSTest 12CH mode.

CRSF Protocol for TBS

T16IZ has been made compatible with the CRSF

(TBS) protocol.

*Bidirectional communication function of CRSF is not supported.

*When using CRSF, the S.BUS servo setting function and

[Reload] [Register] [Change slot] functions cannot be used.

When setting S.BUS servo and sensor, set CRSF to INH.

Tap the "CRSF" button to [ON]. A signal

conforming to the CRSF standard is

output from the S.BUS setting connector

(S.I/F) of the transmitter.

WARNING

Futaba is not responsible for damage

sustained by combination with

parts other than Futaba Genuine

equipment.

● Call page 2/2 from the [System type] menu.

*FASST MULTI/FASST 7CH cannot be selected for Europe.

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды