FUTABA 01000141 Скачать руководство пользователя страница 30

Страница: 30 / 225

Link/Mode Switch

Use the small plastic screw driver that was included

with your receiver.

The Link/Mode Switch is also used for the CH

mode selection.

(The button is not used to link the transmitter and

receiver together. )

Extra Voltage Connector

Use this connector when using a voltage telemetry

device to send the battery voltage information (DC

0 ~ 70 V) from the receiver to the transmitter.

Please use the External voltage input cable.

(UBB0141) This connects directly to your main

motor batteries.

DANGER

Don't touch wiring.

* There is a danger of receiving an electric shock.

Do not short-circuit the battery

terminals.

* A short circuit across the battery terminals may cause

abnormal heating, fire and burns.

Please double check your polarity (+ and

-) when hooking up your connectors.

* If + and - of wiring are mistaken, it will damage, ignite and

explode.

Don’ t connect to Extra Voltage before

turning on a receiver power supply.

Before using the receiver, be sure to read the

precautions listed in the following pages.

Connector

"1 through 6":outputs for the channels 1 through 6

"7/B": outputs of 7 channels and power.
"8/SB": outputs of 8 channels or S.BUS port.

[S.BUS Sevo S.BUS Gyro ]

"S.BUS2": outputs of S.BUS2 port.

[Telemetry Sensor ]

*When using nine or more channels, use an S.BUS

function or use a second R7108SB and link both

to your transmitter.

Connector insertion

Firmly insert the connector in the direction shown

in the figure. Insert the S.BUS2 by turning it 90

degrees.

WARNING

S.BUS2 connectors

Don't connect an S.BUS servo/gyro to

S.BUS2 connector.

LED Monitor

This monitor is used to check the CH mode of the

receiver.

Receiver Nomenclature

Link/Mode

Channels 1 ～ 6

Channel 7 / Battery

Channel 8 or S.BUS

S.BUS2 : Telemetry sensor

or S.BUS2 equipment

＋

－

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды