FUTABA 01000141 Скачать руководство пользователя страница 65

Страница: 65 / 225

Model call

1. Tap the Internal or SD card. Select the

location to which the desired model is to be

saved.

2. Tap the desired model in the model list.
3. Tap the [Select] button.

4. Tap [Yes] to call the model. (When you want

to cancel model call, press [No].)

Model deletion

1. Tap the select model name or the model you

want to delete in the model list.

(The model currently selected cannot be

deleted.)

2. Tap the [Delete] button.

3. Tap [Yes]. (When you want to stop model

deletion, tap [No].)

Blue model would

be deleted.

Blue model was

deleted.

When using model data of T18SZ,

T16SZ, FX-36, FX-32

1.The SD card in which the model data of

another transmitter is saved is displayed on

the model select screen.

T18SZ →　　　　　　 FX-32　→

T16SZ

FX-36

Copy the model data of another transmitter

to T16IZ. The data will be converted for T16IZ.

3. Select the converted model data.

*The model data converted for T16IZ cannot be used in

another transmitter.

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды