FUTABA 01000141 Скачать руководство пользователя страница 54

Страница: 54 / 225

Display

The following LCD screen adjustments:

● Backlighting brightness adjustment
● Backlighting decrease time adjustment
● Touch screen calibration

● Tap the [Display] button in the System menu

to call the setup screen shown below.

●Return to System menu

Backlight max. brightness adjustment

1. Adjust the backlighting brightness with the

value input buttons.

*When the ▲ button is tapped, the backlighting becomes

brighter. When the ▼ button is tapped, the backlighting

becomes darker.

Backlight min. brightness adjustment

1. Adjust the backlight decrease brightness with

the value input buttons.

*When the ▲ button is tapped, the backlighting becomes

brighter. When the ▼ button is tapped, the backlighting

becomes darker.

*It cannot be made brighter than Backlighting brightness

adjustment.

Backlight decrease time

1. You can set a time period to decrease the

LCD backlight. This function counts the period

that the Touch Panel has been not operated.

This time can be set by ten-second steps. You

can also turn off the backlight decrease* if

you like.

*The backlight consumes a large amount of power. We

recommend that you turn off the backlight by setting the

backlight power-off time to about one minute.

Touch calibration

This function adjusts the location of the Touch

Panel. Press the "Touch calibration" button.

The calibration screen will then pop up.

Tap the center of the cross hair cursor on

the screen with the soft pen. As soon as the

system recognizes the position, the cursor

will move on to the next position. Repeat this

procedure as long as the cursor moves to next

position. You will do this five times. Calibration

will be carried out based on the five positions.

Disappearance of the cross hair cursor means

the calibration has been completed.

*In ordinary operation, this calibration is not necessary. If

you notice the Touch Panel is not functioning correctly after

long use, we recommend that you carry out this calibration.

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды