FUTABA 01000141 Скачать руководство пользователя страница 96

Страница: 96 / 225

rpm

Sets the rpm on which

the alarm operates.

↑ An upward arrow

will show that an alarm

will sound when the

rpm rises above the set

value.

↓ A downward arrow

will show that an alarm

will sound when the

rpm falls below the set

value.

Alarm is chosen from

Buzzer, Voice, and

Inhibit.

Allows Speech to be

turned ON or OFF.

● Tap the [ rpm sensor] button in the Telemetry screen

to call the setup screen shown below.

Max. and min. values

s i n c e t h e p o w e r

was turned ON will

display.

*It cannot be used in FASST mode and S-FHSS mode.

*Only receiver voltage and EXT voltage can be used in

FASSTest12CH mode.

*The FASSTest18CH /T-FHSS mode can use all the telemetry

functions.

Type 1

Type 2

Type 3

"Vibrator" type

If the following types are selected, the transmitter

will vibrate during the warning.

Telemetry : RPM Sensor

Displaying data from the rpm

The RPM Sensor screen is used to set up an

optional rpm sensor and display the rotation

information it transmits.

The rotation of the model (engine, motor, etc.)

which is flying can be shown.

If it becomes higher or lower than the setting, an

alarm and/or vibration will alert you.

Alarm set : Over

(

Under

)

rotations

1. Tap Alarm and choose from Buzzer, Voice,

and Inhibit.

2. Choose "Inhibit" for Vibrator if no

using the

vibrator alarm. If using vibrator, choose one

of the three types.

3. Tap to the Limit [

xxx

rpm] item .

4. Adjust the rate using the "▼▼" "▼" "▲" "▲▲"

buttons.

Initial value: ↑

2,000 rpm

↓

0 rpm

Adjustment range: 0 rpm~150,000 rpm

(↑Limit

≧

↓Limit)

*When the screen is tapped for one second, the rate is reset

to the initial value.

5. To terminate the input and return to the

original state, push the HOME/EXIT button.

*An rpm sensor must be installed in the aircraft.

"Magnet"

"Optics"

"Brushless motor"

SBS-01RM →

SBS-01RO →

SBS-01RB →

Gear ratio

Blade

Pole

1.00~99.00

2~10

2~30

●Return to

Linkage menu

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды