FUTABA 01000141 Скачать руководство пользователя страница 95

Страница: 95 / 225

Temperature

Sets the temperature

on which the alarm

operates.

↑ An upward arrow

w i l l s h o w t h a t a n

alarm will sound when

the temperature rises

above the set value.

↓ A downward arrow

w i l l s h o w t h a t a n

alarm will sound when

the temperature drops

below the set value.

Alarm is chosen from

Buzzer, Voice, and

Inhibit.

Allows Speech to be

turned ON or OFF.

● Tap the [Temperature] button in the Telemetry

screen to call the setup screen shown below.

Max. and min. values

s i n c e t h e p o w e r

was turned ON will

display.

Telemetry : Temperature

Displaying data from the temperature

Temperature is a screen which displays/sets up

the temperature information from an optional

temperature sensor.

The temperature of the model (engine, motor,

battery, etc.) which is flying can be displayed.

If it becomes higher or lower than the setting, an

alarm and/or vibration will alert you.

Alert set : Temperature warning

1. Tap Alarm and choose from Buzzer, Voice,

and Inhibit.

2. Choose "Inhibit" for Vibrator if no

using the

vibrator alarm. If using vibrator, choose one

of the three types.

3. Tap to the Limit [

℃

] item .

4. Adjust the rate using the "▼▼" "▼" "▲" "▲▲"

buttons.

Initial value: ↑100

℃

↓0

℃

Adjustment range: -20

℃

~200

℃

(↑Limit

≧

↓Limit)

*When the screen is tapped for one second, the rate is reset

to the initial value.

5. To terminate the input and return to the

original state, push the HOME/EXIT button.

*A temperature sensor must be installed in the aircraft.

*It cannot be used in FASST mode and S-FHSS mode.

*Only receiver voltage and EXT voltage can be used in

FASSTest12CH mode.

*The FASSTest18CH /T-FHSS mode can use all the telemetry

functions.

Type 1

Type 2

Type 3

"Vibrator" type

If the following types are selected, the transmitter

will vibrate during the warning.

●Return to

Linkage menu

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды