FUTABA 01000141 Скачать руководство пользователя страница 28

Страница: 28 / 225

1）

Rotate the antenna.

2）

Open the rubber cover and insert the

micro SD card into the micro SD card slot.

Card slot

SD card slot

*Pay attention to the proper

orientation of the SD card, as

shown here.

3）

When the micro SD card is pressed in once

again, the card will be released from the

card slot and can be removed.

micro SD card (secure digital memory card) (not included)

The T16IZ transmitter model data can be stored by using any commonly

found micro SD card. When T16IZ update software is released, the software is

updated using an micro SD card. The T16IZ is capable of using SD and SDHC

cards (SD:32MB-2GB SDHC:4GB-32GB).

micro SD card reader/writer

Saving model data and update files (released from

Futaba) into the micro SD card, you can use those

files on your T16IZ transmitter. Equipment for

reading and writing SD cards is available at most

electronics stores.

Stored data

When you have a problem of saving or reading data

after a long period of use, please get a new micro

SD card.

*We are not responsible for, and offer no compensation for,

memory card data that fails or is damaged for any reason.

Be sure to keep a backup of all important data stored in your

micro SD card.

Inserting/removing the micro SD card

The micro SD card slot is shown in the next figure.

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды