FUTABA 01000141 Скачать руководство пользователя страница 169

Страница: 169 / 225

169

Gyro　[Helicopter]

Use this when you want

to adjust sensitivity via

VR, etc., and not on-

screen data entry. Tap "--

", select "VR", etc., and

then tap the value to

adjust. (Won't operate

when value is "0".)

The operation mode

( AV C S / N O R ) a n d

sensitivity of the 3

axes Gyro/Gyro2/

Gyro3 can be set.

Tapping these will

pull up the detailed

selection screen for

each.

Rate1 Gyro type and

gain

Rate2 Gyro type and

gain
Rate3 Gyro type and

gain

The ON/OFF switch

of gyro is chosen.

When using Rate2/Rate3, make it

INH → ON or OFF.

Gyro（RUD)

setting

Gyro2（AIL)

setting

Gyro3（ELE)

setting

3 rate (gyro gain)

adjustment

Condition group/

single mode selection

(Gr. /Sngl)

This function is used to adjust gyro sensitivity. The

sensitivity and operation mode (Normal mode/

AVCS mode) can be set for each condition.

The gyro sensitivity can be switched with each

condition or the switch. (3 sensitivities)

*Compatible with 3 axis gyro (CGY750).

Setting method

● When using this function, Tap [INH]. (ON is

displayed.)

● When you want to set the same contents at

other conditions, select the group mode.

When you want to set the selected condition

only, select the single mode (initial setting).

● Three rates can be switched for each

condition. (Rate 1/Rate 2/Rate 3)

● A fine tuning VR can be set.

● Select [Gyro] at the

model menu and call

the setup screen.

Note: [Gyro] [Gyro2] [Gyro3] Default function
[Gyro]:

CH6

(FASSTest12CH)

CH5

(Other system type)

[Gyro2] :

CH9

[Gyro3] :

CH10

Always set to [--] both (control) and (trim) for

the [Gyro] function at the Function menu in

the Linkage menu.

●Return to Model menu

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды