manualshive.com logo in svg

FUTABA 01000141, Полное руководство

FUTABA 01000141 - полная инструкция пользователя для скачивания бесплатно. Подробный мануал содержит все необходимые сведения о продукте. Скачайте его с manualshive.com прямо сейчас и ознакомьтесь со всеми функциями и возможностями этого устройства.

Поделиться
Скачать
background image

10

Features 

FASSTest system

The T16IZ transmitter has adopted the bidirectional communication system "FASSTest". Data from the receiver can be checked in 

your transmitter. FASSTest is a maximum 18 channels 2.4 GHz dedicated system.

Color touch screen LCD

T16IZ has an HVGA 4.3 inch, full-color, backlit LCD touch screen. The screen is transflective which enables both indoor and 

outdoor visibility.

S.BUS2 system

By using the S.BUS2 system multiple servos, gyros and telemetry sensors are easily installed with a minimum amount of cables.  

Model types

Multicopter. 8 swash types are available for helicopters. 7 wing types and 3 tail types are available for airplanes and gliders. 

Functions and mixing functions necessary for each model type are set in advance at the factory.

Lithium-ion polymer battery

T16IZ is operated by a 7.4 V/2,000 mAh Lithium-ion polymer battery.

micro SD card (Secure Digital memory card) (Not included)

Model data can be saved to an micro SD card (SD:32MB-2GB SDHC:4GB-32GB). When T16IZ transmitter software files are 
released, the software can be updated by using an micro SD card update.

Edit button

Two edit buttons are provided, and the operating screen can be immediately “Returned” to the HOME screen during operation. 
Setting operation can be performed easily by combining this button with a touch sensor.

Vibration function

Selects a function that alerts the operator to various alarms by vibrating the transmitter in addition to sounding a buzzer.

Speech function

A function is equipped which allows the system to provide telemetry data audibly.  This function can also be utilized with 

commercially available earphones.

Contents and Technical Specifications

(Specifications and ratings are subject to change without notice.)

• T16IZ Transmitter
• R7108SB Receiver 
• LT2F2000B LiPo Battery

Transmitter T16IZ 

(2-stick, 18-channel, FASSTest-2.4 GHz system) 

Transmitting frequency: 2.4 GHz band

System: FASSTest 18CH/FASSTest 12CH/S-FHSS/T-FHSS/

               FASST MULT(Europe is not supported)/FASST 7CH(Europe is not supported) switchable  

Power supply: 7.4

 

V LT2F2000B LiPo battery 

Frequency band: 2.4 GHz

RF power output : 100 mW EIRP

Receiver R7108SB

(FASSTest-2.4 GHz system, Dual Antenna Diversity, S.BUS/S.BUS2 system)

Power requirement: 3.7 V-7.4 V battery or regulated output from ESC, etc. (*1)

Size: 0.98 x 1.86 x 0.56 in. (24.9 x 47.3 x 14.3 mm)

Weight: 0.42 oz. (12.0 g)

Frequency band: 2.4 GHz 

RF power output:  25 mW EIRP

(*1) When using ESCs make sure that the regulated output capacity meets your usage application.

Note: This set does not include a charger. Use a commercially available USB charger AC 

adapter (USB-A type 5 V-2 A) or the Futaba optional USB AC adapter.
Note: The battery in the T16IZ transmitter does not arrive already attached to the battery 

connector.  Please connect the battery connector before use.

• USB Cable
• Hex Key 
• Tx Strap 

• Short Manual 

*The contents may vary on the type of set.

Содержание 01000141


































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 01000141

Balboa GL Series User Manual preview
GL Series
Бренд: Balboa Страницы: 12
Paoli F1 Operating And Maintenance Manual preview
F1
Бренд: Paoli Страницы: 16
IBM 3708 End-User Reference preview
3708
Бренд: IBM Страницы: 144
Warren Controls E024 Installation, Operation And Maintenance Instructions preview
E024
Бренд: Warren Controls Страницы: 28
EAS Electric ECRP86EKD Operating Manual preview
ECRP86EKD
Бренд: EAS Electric Страницы: 89
Samson 3354 Mounting And Operating Instructions preview
3354
Бренд: Samson Страницы: 40
Ultra Start 15 SERIES Owner'S Manual preview
15 SERIES
Бренд: Ultra Start Страницы: 8
LAE electronic LF28 Instructions For Installation And Use Manual preview
LF28
Бренд: LAE electronic Страницы: 7
LAE electronic AT1-5 Instructions For Use preview
AT1-5
Бренд: LAE electronic Страницы: 2
olympia electronics GR-6500 Quick Installation Manual preview
GR-6500
Бренд: olympia electronics Страницы: 10
Water Furnace IntelliZone2 MasterStat Specification Catalog And Design Manual preview
IntelliZone2 MasterStat
Бренд: Water Furnace Страницы: 44
YASKAWA Motoman MLX200 Hardware Installation & Software Upgrade preview
Motoman MLX200
Бренд: YASKAWA Страницы: 121
YASKAWA Varispeed f7 Technical Manual preview
Varispeed f7
Бренд: YASKAWA Страницы: 17
YASKAWA SI-EM3D Technical Manual preview
SI-EM3D
Бренд: YASKAWA Страницы: 58
YASKAWA 1000-Series Installation Manual preview
1000-Series
Бренд: YASKAWA Страницы: 30
Data Signs PTL Compact 2 Operation And Maintenance Manual preview
PTL Compact 2
Бренд: Data Signs Страницы: 23
RAKwireless WisLink LPWAN RAK5146 User Manual preview
WisLink LPWAN RAK5146
Бренд: RAKwireless Страницы: 9
NOCO Genius CURTIS DC Series Installation Instruction preview
CURTIS DC Series
Бренд: NOCO Genius Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды