FUTABA 01000141 Скачать руководство пользователя страница 171

Страница: 171 / 225

171

Governor

When using a Futaba governor, this function is

used to switch the RPM of the helicopter's head.

Up to 3 rates can be set for each condition.

*The governor is used by connecting the governor speed

setting channel to CH7 (initial setting).

*When using an independent governor [ON]/[OFF] switch,

connect the AUX([ON]/[OFF]) connector of the governor to

CH8 (initial setting) and set the switch to CH8 (Governor2)

at the Function menu of the Linkage menu.

*When using the Fuel Mixture function, the mixture servo

is controlled from the governor. When transmitting the

mixture curve data from the transmitter to the governor, the

governor AUX (m.trm) connector must be connected to CH8

(initial setting) and governor side setting performed. See the

governor instruction manual.

Note: Always set (Control) and (Trim) to [--] for

[Governor] and [Governor 2] of the Function menu

of the Linkage menu.

● Select [Governor] at the model menu

and call the setup screen shown below.

Fine tuning VR settings

RPM adjustment

Unit display selection:

[%] [rpm]

Setting method

●Activate the mixing

When using this function, Tap [INH]. (ON is

displayed.)

*When the function is set ON/OFF at the governor setup

screen, the governor rpm setting channel end point servo

travel and limit point are now initialized.

*When changed from INH to ACT (ON), the servo travel is

initialized to 100 and the limit point is initialized to 155.

*When operation is changed to INH at all conditions, the

servo travel is initialized to 100 and the limit point is

initialized to 135.

●RPM adjustment

Tap to the rate item .

Adjust the rpm using the "▼▼" "▼" "▲" "▲▲"

buttons.

Initial value: 50% (1500rpm)

Adjustment range: OFF, 0~110% (OFF,

700~3500rpm)

*When the value is tapped reset to the initial value.

●Unit display selection

Tap to the UNIT item [%] [rpm]. Select the

unit.

●Return to Model menu

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды