manualshive.com logo in svg

FUTABA 01000141, Полное руководство

FUTABA 01000141 - полная инструкция пользователя для скачивания бесплатно. Подробный мануал содержит все необходимые сведения о продукте. Скачайте его с manualshive.com прямо сейчас и ознакомьтесь со всеми функциями и возможностями этого устройства.

Поделиться
Скачать
background image

144

Gyro

[Corresponding model type]: Airplane/glider/multicopter, general

This function is used when a GYA Series gyro 

is used to stabilize the aircraft's attitude. The 

sensitivity and operation mode (Normal mode/GY 

mode) can be switched with a switch.

● Three rates (Rate 1/Rate 2/Rate 3) can be 

switched.

● Up to 3 axes (Gyro/Gyro 2/Gyro 3) can be 

simultaneously controlled.

*Initial setting does not assign a sensitivity channel. Use the 

Function menu of the Linkage menu to assign the sensitivity 

channel (Gyro/Gyro2/Gyro3) used to a vacant channel 

beforehand.

   Set [Control] and [Trim] other than Function to [--].

● Three rates (Rate 1/Rate 2/Rate 3) can be used.

  Tap to the [Rate] item. Adjust the rate.

● When using this function, Tap [INH]. 
● When a Futaba GYA gyro is used, when [GY] type is selected, the 

sensitivity set value is directly read in both the AVCS and Normal modes.

● When setting a switch, tap the Switch item and tap the "--" button to call 

the selection screen, and then select the switch and set its ON direction.

  (For a description of the switch selection method, see the description at 

the end of this manual.)

● Select [Gyro] at the model menu and 

call the setup screen shown below.

The operation mode 

(AVCS/NOR) and 

sensitivity of the 3 

axes Gyro/Gyro2/

Gyro3 can be set.

3 rate (gyro gain)

adjustment

Condition group/

single mode selection 

(Gr. /Sngl)

The ON/OFF switch of 

gyro is chosen.

Tapping this will change INH to either ON or OFF 

and enable operation. Adjustment of the three 

rates (sensitivity) and switching between Normal 

and AVCS is possible.

●Return to Model menu

Содержание 01000141


































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 01000141

C.Nord GSM Operation Manual preview
GSM
Бренд: C.Nord Страницы: 100
3Com CoreBuilder 9000 Getting Started Manual preview
CoreBuilder 9000
Бренд: 3Com Страницы: 78
Wavelink Avalanche User Manual preview
Avalanche
Бренд: Wavelink Страницы: 69
Danfoss VLT MCD 200 Installation Manual preview
VLT MCD 200
Бренд: Danfoss Страницы: 32
Danfoss PVG 16 PVH/Covers Technical Information preview
PVG 16 PVH/Covers
Бренд: Danfoss Страницы: 112
Danfoss PVG 100 Service And Parts Manual preview
PVG 100
Бренд: Danfoss Страницы: 44
Danfoss PVG 16 PVH/Covers Service And Parts Manual preview
PVG 16 PVH/Covers
Бренд: Danfoss Страницы: 144
Danfoss VLT LCP 11 Installation Instructions preview
VLT LCP 11
Бренд: Danfoss Страницы: 2
Danfoss VLT FC Series Operating Instructions Manual preview
VLT FC Series
Бренд: Danfoss Страницы: 64
Danfoss EKC 102A Instructions Manual preview
EKC 102A
Бренд: Danfoss Страницы: 8
Danfoss VLT AutomationDrive FC 360 Programming Manual preview
VLT AutomationDrive FC 360
Бренд: Danfoss Страницы: 60
Danfoss DHP-A Installation Instruction preview
DHP-A
Бренд: Danfoss Страницы: 6
Danfoss AMV 110 NL AQT Datasheet preview
AMV 110 NL AQT
Бренд: Danfoss Страницы: 4
Danfoss VLT FC Series Installation Manual preview
VLT FC Series
Бренд: Danfoss Страницы: 8
Danfoss AK-CC 550A Troubleshooting Manuallines preview
AK-CC 550A
Бренд: Danfoss Страницы: 2
Danfoss ECL Comfort 110 Quick Manual preview
ECL Comfort 110
Бренд: Danfoss Страницы: 2
Danfoss 103E5 Installation & User'S Instructions preview
103E5
Бренд: Danfoss Страницы: 24
Eaton TS110 Product Manual preview
TS110
Бренд: Eaton Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды