FUTABA 01000141 Скачать руководство пользователя страница 105

Страница: 105 / 225

105

Telemetry : GPS [Speed]

Displaying data from the speed

The speed screen displays and sets the speed data from an

SBS-01/02G (GPS sensor) sold separately.

The speed of the aircraft during flight can be displayed.

After flight, the maximum speed during flight can be

viewed. Because this speed is based on position data from

a GPS satellite, the ground speed is displayed instead of

air speed. Consequently, with a head wind, the displayed

speed decreases and with a tail wind, the displayed speed

increases.

*A GPS sensor must be installed in the aircraft.

Alarm setting when speed increases

1. Tap Alarm and choose from Buzzer, Voice, and

Inhibit.

2. Choose "Inhibit" for Vibrator if no

using the vibrator

alarm. If using vibrator, choose one of the three

types.

3. Tap Limit [xxx km/h].

4. Adjust the rate using the "▼▼" "▼" "▲" "▲▲"

buttons.

Initial value: ↑200km/h ↓0km/h

Adjustment range 0km/h~500km/h

(↑Limit

≧

↓Limit)

*When the screen is tapped for one second, the rate is reset

to the initial value.

5. To terminate the input and return to the original

state, push the HOME/EXIT button.

*Speed alarm precaution

Since the GPS speed sensor displays the ground speed, it

cannot be used as a stall alarm. For example, an aircraft that

stalls at 50km/h will stall if the tailwind is 5km/h or greater

even through 55km/h is displayed by ground speed. In

addition, with an aircraft that will disintegrate in midflight at

400km/h at an over-speed alarm, when the headwind reaches

30km/h the airplane will disintegrate in midair due to over

speeding even at a ground speed of 370km/h.

Sets the speed on

which the alarm

operates.

● Tap the [GPS] button in the Telemetry screen to call

the setup screen shown below.

Max. and min. values

s i n c e t h e p o w e r

was turned ON will

display.

Speed

Alarm is chosen from

Buzzer, Voice, and

Inhibit.

Allows Speech to be

turned ON or OFF.

Type 1

Type 2

Type 3

"Vibrator" type

If the following types are selected, the transmitter

will vibrate during the warning.

*The GPS sensor is necessary, and is sold separately. Mount

and connect the sensor in accordance with the sensor

instruction manual.

*It cannot be used in FASST mode and S-FHSS mode.

*Only receiver voltage and EXT voltage can be used in

FASSTest12CH mode.

*The FASSTest18CH /T-FHSS mode can use all the telemetry

functions.

↑ An upward arrow

indicates the alarm

will sound when the

speed reaches above

your set value.

↓ A downward arrow

indicates the alarm

will sound when the

speed reaches below

your set value.

Reference and Distance mode work in conjunction with Distance

discussed on the previous two pages.

●Return to

Linkage menu

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды