FUTABA 01000141 Скачать руководство пользователя страница 222

Страница: 222 / 225

222

7. When the software update is completed,

"Completed" message is shown on the LCD

display of your T16IZ. (Show below picture.)

8. Turn off the power switch of your T16IZ and

remove the SD card from the card slot.

Possible Problems

When one of the error messages shown

below appears on the LCD screen your

T16IZ, the software update will not be

completed.

"Low battery."

Software update is postponed because

of low battery. Retry the software update

after the battery is recharged.

"Update file not found."

The T16IZ cannot find the update file on the

SD card. Check to be sure all the update

files have been copied onto the SD card.

"Broken file."

The T16IZ detects the update file error. The

update file may be broken or for another

transmitter.

"Write error."

The software update procedure is stopped

for an unknown reason. Contact your local

service center when this error message

appears on the LCD screen of your T16IZ.

Don't absolutely remove the battery

and the SD card from the transmitter

during the update.

There is a possibility that the transmitter

will be damaged.
Recovering a failed update
If you failed to update for any reason, it

may transmitter will not start.
In that case, please update again

transmitter in the following procedure.

1. Detach the battery from the transmitter.
2. Insert the SD card that contained the

update files to the transmitter.

3. Attach the battery to the transmitter

while pressing down the "HOME/EXIT"

button.

4. The update will start.

Even after the above steps, if the

transmitter fails to update or does not

start, please have it serviced.

Complete

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды