FUTABA 01000141 Скачать руководство пользователя страница 210

Страница: 210 / 225

210

Operations related to servo speed

Servo speed setting

The servo speed at each function

operation (including flight condition
switching) can be adjusted. The servos

operate smoothly at a fixed speed
corresponding to the set speed. The

operating speed (In side) and return speed
(Out side) can be set individually.

Switch the operation mode according to

the set function.

"Symmetry" mode: Used with ailerons

and other self neutral functions.

"Linear" mode: Used with functions

which hold the operation position of

the throttle and switch channel, etc.

[Setting method]

1. Select the mode ([Linear] or

[Symmetry]). Each time the button is

tapped, it toggles between [Linear]

and [Symmetry].

2. Tap the In or Out Speed button and

set the servo speed.

Initial value: 0

Setting range: 0~27

（First）0 ～ 27（Slowly）

In speed

Out speed

In case of Symmetry

In case of Linear

Out speed

In speed

Symmetry

Speed

Out

Speed

Out

Speed

Linear

Speed

Out

Speed

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды