FUTABA 01000141 Скачать руководство пользователя страница 147

Страница: 147 / 225

147

[Corresponding model type]: Airplane/glider general

Acceleration

Setting method

● Acceleration rate setting (Rate)
● The return time after operation (Damping)

can be set.

● The operation point at acceleration

and deceleration can be set. When an

operation point is exceeded, acceleration is

performed.

● Select [Acceleration] at the model

menu and call the setup screen shown

below.

Acceleration setting can be performed at Elevator,

Elevator → Camber and Aileron → Rudder. (Glider

only)

● This setting is divided into elevator setting and camber

setting. The setting method is the same.

● Camber setting sets the acceleration function for Ele

to camber mixing. Setting is not performed when Ele to

camber mixing is INH.

● The acceleration function can be set for both the up

side and down side.

● Function ON/OFF switch setting is performed for

Aileron→ Rudder setting only.

● Aileron→ Rudder setting is acceleration

function setting for Aileron→ Rudder mixing. It is not

performed when Aileron→ Rudder mixing is INH.

Note: When using the acceleration function,

since the servo stroke is large, make your

settings so there is no binding of your linkage.

Operation up to this

range will initiate

acceleration.

Act position

The rate the angle

increases.

To next page

2/3 : Elevator → Camber

3/3 : Aileron → Rudder

The return time after operation (Damping)

can be set.

（First return）1 ～ 100（Slow return）
（Acceleration doesn't function as 0.）

When using this

function, Tap [INH].

(ON is displayed.)

Condition group/

single mode selection

(Gr. /Sngl)

Current position

●Return to Model menu

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды