FUTABA 01000141 Скачать руководство пользователя страница 173

Страница: 173 / 225

173

B. Wireless tunings: Gyro tunings can be made wirelessly. (Limited items)

T16IZ

CGY755/CGY760R

For CGY755

(For CGY760R Use other receiver)

S.BUS2 Receiver

Wireless Tunings function list

Do not set during flight. Make settings when

the aircraft is on the ground and the motor

and engine are stopped.

-FLT. TUNE

Base Gain: Gyro base gain setting

CYC. Rt: Cyclic rate setting

Cnt. AuthAIL: Control Authority Aileron

Cnt. AuthELE: Control Authority Elevator

EXPO.: Exponential

FLT. Styl: Flight style

ELE. Comp: Elevator pre compensation

-SWH. BASIC

SWS. Rate: Rate adjustment

PIT. Rate: Rate adjustment

SWS. Ring

- Governor Basic

GOV Gain: Governor gain

L Lmt. L rpm : Low limit hovering RPM

L Lmt. H rpm : Low limit idling RPM

-Flight Tune Expert

HeadHld A : Head hold aileron

StopTune A : Stop tune aileron

HeadResp: Head Response

HeadHld E: Head hold elevator

StopTune E : Stop tune elevator

-Rudder Expert

EXP. AVCS: Rudder exponential AVCS

EXP. NORM: Rudder exponential NORMAL

CNT. DlIn: Control delay in

CNT. DlOut: Control delay out

ANG: Pirouette speed

Tail Resp: Tail response

A. Wired connection: Advanced settings (all functions same as GPB-1)

T16IZ

S.I/F

P.BOX

CGY Connection Cable (included with gyro)

CGY755/CGY760R

● Connect the receiver battery (3.5 to 8.4 V) to

one of the "AIL" to "S.B2" connectors other

than "RPM" and "P.BOX".
(Do not connect to "RPM" and "P.BOX".)

Notes

If the T16IZ and gyro are not connected, the

gyro setting value cannot be changed.

Notes

When using the wireless tuning function, set

the telemetry function to ACT.

The wireless tuning can be FASSTest or

T-FHSS.

Gyro setting

The T16IZ has the same functions as the GPB-1.

The CGY755 / CGY760R can be set up from the

T16IZ screen by connecting to the T16IZ. Some

functions can be set wirelessly.

*CGY760R needs to be Ver3.0 ~. Update CGY760R.

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды