FUTABA 01000141 Скачать руководство пользователя страница 115

Страница: 115 / 225

115

3. Select the operating mode for each channel.

"NORM": The model is controlled by signals

from the student transmitter.

"MIX" mode: The model is controlled by

signals from the teacher and student

transmitters. (Reset the student's model data

to the default condition.)

"FUNC" mode (function mode):
The model is controlled by signals from

the student transmitter with the teacher

AFR setting. (Reset the student's model data

to the default condition.)

"OFF": Only the teacher side operates.

*The setting above allows setting of the servo throw relative

to the amount of student side operation when [MIX] or

[FUNC] was selected.

When changing the rate, use the "▼▼" "▼"

"▲" "▲▲" button to Tap the [Rate] item of

the channel.

Setting range: -100~+100
Initial value: +100

*When the value is tapped, the rate is reset to the initial value.

4. Set the switch of each channel.

*When setting the switch at each channel, tap to the "SW"

item of the channel you want to change, call the switch

setup screen, and select the switch.

"--" : Always ON.
"SA"~"SH": The switch which enables student

side operation can be selected. (See "Switch

selection method" at the end of this manual

for selection method details.)

Trainer student channel setting

function

In training mode, the instructor's transmitter can

pick up the student's signal on both the "Function"

and "Mix" channels. That makes it easy for the

two transmitters to connect even if the student and

instructor have set up their transmitters differently.

*When the instructor's transmitter mode is set to "NORM",

the signal of the same channel of the student's transmitter is

output as is. (The same as before.)

Futaba is not responsible for damage

sustained by combination with parts other

than Futaba Genuine equipment.

When connecting Futaba transmitters to

the trainer code, do not operate the power

switch on the student side transmitter and

operate the power switch on the teacher

side transmitter as before. The student side

transmitter turns power automatically in

conjunction with the teacher side.

Trainer connector power supply

specification

Trainer connector to supply power to external

equipment connected to the trainer connector, when

turning on the power by pressing the power switch

in the trainer student mode.

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды