FUTABA 01000141 Скачать руководство пользователя страница 66

Страница: 66 / 225

WARNING

Never launch the Model Selection function

while the engine is starting or the motor drive

wiring is connected.

■ Careless spinning of propellers or rotors is extremely

dangerous.

WARNING

Carefully check that the aircraft to be used and

the model selected match up.

■ Using a model which does not match the aircraft runs

the risk of the aircraft flying out of control and crashing.

Perform a careful operations check prior to flight.

Model name change

1. The model data chosen at current model

can be changed. The current model name,

tap.

2. When [Rename] is tapped, a keyboard

appears on the screen.

3. Enter the model name from this keyboard.

*Up to 15 characters can be input at the model name.

Model copy

1. The model data chosen at current model

can be copied. The current model name,

tap.

2. Tap the "Copy" button and tap the

destination button and select the copy

storage destination. (Internal or SD card)

3. When [Internal]or [SD card] is tapped,

copying is executed.

*If there is no model with the same name in the copy

destination, the name of the copied model is saved. If there

is a model of the same name, a number is added at the end

of the model name and the model is copied. You can change

the name later.

*Indication date : When the model data is copied, the creation

date for the current model is recorded.

*T16IZ can use model data of T16SZ, T18SZ, FX-36, FX-32.

Other transmitter model data is not available. However, if

the model data conversion function (described at the end of

this manual) is used, part of the model data of T14SG, FX-

22, T12K can be used.

Current model (green)

is chosen (blue).

Current model (green)

is chosen (blue).

add new copied model

Completion of rename

When you are done

renaming, tap Model name.

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды