FUTABA 01000141 Скачать руководство пользователя страница 166

Страница: 166 / 225

166

● Mixing curve setting

*For a description of the curve setting method,

see the description at the back of this manual.

Throttle mixing

This function corrects slowing of engine speed

caused by swash plate operation during aileron

or elevator operation. The method of applying

clockwise or counterclockwise torque when

pirouetting can also be corrected.

An acceleration function which temporarily

increases the throttle side correction rate relative to

rapid stick operation can also be set.

Setting example

● Aileron to Throttle applies a load to the

engine and corrects slowing of the

engine speed when the aileron stick was

operated. Engine racing can be adjusted

independently at the right aileron and left

aileron by Rates A and B.

Setting method

● When using this function, Tap [INH]. (ON is

displayed.)

● When you want to set the same contents at

other conditions, select the group mode.

When you want to set the selected condition

only, select the single mode (initial setting).

● The correction rate can be set by curve.
● A switch can be set.

When [--] is set, the swash mixing function is

operated by merely selecting the condition.

When setting an [ON]/[OFF] switch, tap to

the [--] item and tap the screen to call the

selection screen and set the switch and its

ON position.

When correction is necessary, tap to the mixing

item corresponding to the mixing that needs

correction and tap the screen to call the curve setup

screen, and then correct the slowing.

<Acceleration function setting>

● Acceleration can be set for both settings

(Left) and (Right)

● Acceleration rate setting (Rate)
● The return time (Damping) after operation

can be set.

● The operation point (Act position) when the

correction rate is increased and decreased

can be set independently. When an

operation point is exceeded, acceleration

operation is performed.

● Select [Throttle mixing] at the model

menu and call the setup screen shown

below.

"Linear" : Correction

applied for the entire

throttle range.

"CTRM" : The correction

rate maximum when

the throttle stick is

centered.

●Return to Model menu

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды