FUTABA 01000141 Скачать руководство пользователя страница 29

Страница: 29 / 225

Open the rubber cover

CAUTION

Be sure to turn off the power to

the transmitter before inserting or

removing the micro SD card.

As the micro SD card is a precision

device, do not use excessive force when

inserting.

-When an micro SD card is installed in

the T16IZ transmitter, a folder called "Fu

taba" is created. Folders called "LOG" and

"MODEL" are created in this folder. The

"MODEL" folder stores the model data and

the "LOG" folder stores the telemetry log

data.
-The telemetry log data recorded on the

micro SD card can be converted to CSV

format by the telemeter log converter re-

leased on our home page. When copying or

moving a log file, always select both .FLI

and .FLD file.

Connector for trainer function

When you use the trainer function, connect the

optional trainer cable between the transmitters for

teacher and student.

*You can set the trainer function on the Trainer Function

screen in the System menu.

Connector/Plug

Trainer

Connector

S.BUS (S.I/F)

Connector

Earphone

Plug

S.BUS connector (S.I/F)

When using an S.BUS servo and telemetry sensor,

connect them both here.

Earphone plug

Connecting a stereo headphone to this plug, the

speech information of telemetry can be heard.

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды