FUTABA 01000141 Скачать руководство пользователя страница 86

Страница: 86 / 225

● Tap the [Function name] button in the Linkage

menu to call the setup screen shown below.

Function name

Function name can be changed

The name of the spare functions (Auxiliary 1-8)

can be changed for the full name (10 characters) or

for the abbreviated name (4 characters).

Function name change method

1. Select [Function name] from the Linkage

menu and tap the screen.

2. The Function name setup screen is displayed.
3. When the function whose name is to be

changed is selected and the screen is

tapped, a modification screen is displayed.

4. Select the function to be renamed and

select [Rename] and tap the screen. A

character input screen is displayed. Input the

function name.

5. When [Reset] is selected and the screen is

held down, the function name is set to the

initial state function name.

6. The function name may be displayed in 10

characters or 4 characters, depending on

the setup screen. For 4-character display,

input the function name as required.

●Return to Linkage menu

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды