FUTABA 01000141 Скачать руководство пользователя страница 101

Страница: 101 / 225

101

*It cannot be used in FASST mode and S-FHSS mode.

*Only receiver voltage and EXT voltage can be used in

FASSTest12CH mode.

*The FASSTest18CH /T-FHSS mode can use all the telemetry

functions.

Telemetry: Voltage [Battery]

Displaying data from the receiver battery voltage

In this screen, the battery voltage of a receiver is

displayed.

If it becomes higher or lower than the settin, an

alarm and/or vibration will alert you.

Battery voltage

Sets the voltage on

which the alarm

operates.

↓ The "down" arrow

will indicate that an

alarm will sound when

the voltage drops to

below the setting.

Alarm is chosen from

Buzzer, Voice, and

Inhibit.

Allows Speech to be

turned ON or OFF.

● Tap the [Voltage] button in the Telemetry screen

to call the setup screen shown below.

Max. and min. values

s i n c e t h e p o w e r

was turned ON will

display.

In this screen, the battery voltage is displayed.

order to use this function, it is necessary to connect

External voltage connector of R7108SB

⇔

SBS-

01V

⇔

Battery

SBS-01V measures two batteries. The power

battery connected to two lines is displayed on EXT-

VOLT. The battery for receivers connected to 3P

lines is displayed here.

*SBS-01V must be installed in the aircraft.

＜

Two examples of wiring are shown

＞

*Refer to the manual of SBS-01V for the details of

wiring.

to S.BUS2

port

to S.BUS2

port

R7108SB

Drive battery 1

（EXT Battery)

Receiver battery

Drive battery 2

（EXT Battery)

Drive battery 1

（EXT Battery)

Drive battery 2

（EXT Battery)

Switch

Power supplies

for servos

Another power

supply Hub

S.BUS2

servos

Two drive batteries are measured (R7108SB use)

Two drive batteries and power supplies for servos are measured (R7108SB use)

●Battery voltage measurement for receivers [R7108SB use]

●The drive battery 1 is measured in an EXT port [R7108SB use]

●The drive battery 2 is measured in an EXT line [SBS-01V use]

●Battery voltage measurement for receivers [R7108SB use]

●The drive battery 1 is measured in an EXT port [R7108SB use]

●The drive battery 2 is measured in an EXT line [SBS-01V use]

●The voltage for servos is measured in a power supply line [SBS-01V use]

Normal Line

EXT Line

*SBS-01V measures two voltage. One corresponds to high voltages, such as a drive battery,

with an EXT line. Another is a normal line and is measurement of the battery for receivers of a

line connected to 3P connector, or the battery for servos.

Alarm set

1. Tap Alarm and choose from Buzzer,

Voice, and Inhibit.

2. Choose "Inhibit" for Vibrator if no

using

the vibrator alarm. If using vibrator,

choose one of the three types.

3. Tap to the Limit [4.0 V] item .

4. Adjust the rate using the "▼▼" "▼" "▲"

"▲▲" buttons.

Initial value: 4.0 V
Adjustment range: 0.0 V~100.0 V

*When the screen is tapped for one second, the rate is

reset to the initial value.

5. To terminate the input and return to

the original state, push the HOME/EXIT

button.

Vibrator choices are

type1-3, and Inhibit.

●Return to

Linkage menu

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды