FUTABA 01000141 Скачать руководство пользователя страница 32

Страница: 32 / 225

Output

connector

Channel

Mode A

～

8CH

Mode B

～

7CH

Mode C

～

16CH

Mode D

～

15CH

7/B

8/SB

S.BUS

Red LED

blink

1 time

2 times

3 times

4 times

R7108SB CH Mode table

Default

Channel Modes

The R7108SB is capable of changing its channel allocations as

described in the table below. This is especially important when

using the receiver in a dual receiver mode.

Turn on the receiver. [Transmitter is always OFF]

Press and hold the Link/Mode button for 5 seconds to 10

seconds.

When the LED of the receiver changes from blinking red

to blinking red with green, Link/Mode button is released.

The LED should now blink red two times in the patterns

described in the chart below.

Each press of the Link/Mode button advances the

receiver to the next mode.

When you reach the mode that you wish to operate in,

press and hold the Link/Mode button for more than 2
seconds.

When LED blinks in green with red, it is the

completion of a mode change, Link/Mode button is
released.

Please cycle the receiver power off and back on again

after changing the Channel mode.

LED Indication

System

Status

LED

FASSTest

No signal reception

Red Solid

Receiving signals

Green Solid

Waiting for link

Start → 2second

later → Red

Blink（1second）

FASST

No signal reception

Red Solid

Receiving signals

Green Solid

Receiving signals

but ID is unmatched

Green Blink

Waiting for link

Red Blink

FASSTest

FASST

Unrecoverable error

(EEPROM, etc.)

Alternate blink

Green LED

blink

System

1 time

FASSTest

2 times

FASST Multi-ch Normal mode

3 times

FASST Multi-ch High-speed mode

4 times

FASST 7ch Normal mode

5 times

FASST 7ch High-speed mode

R7108SB System table

FASST mode cannot use telemetry functions.

Systems (FASSTest ⇔ FASST) change method

Turn on the receiver. [Transmitter is always OFF]

Press and hold the Link/Mode button for 10 seconds to 15 seconds.

When the LED begins to blink green the button may be released.

The LED should now be blinking green in one of the patterns

described by the chart below.

( Default : FASSTest )

Each press of the Link/Mode button advances the receiver to the

next system.

When you reach the system that you wish to operate in, press and

hold the Link/Mode button for more than 2 seconds.

When the LED

blinks green and red, the system change is complete. Release the
Link/Mode button.

Please cycle the receiver power off and back on again after

changing the system.

Default

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды