FUTABA 01000141 Скачать руководство пользователя страница 67

Страница: 67 / 225

Model type

This function selects the model type from among airplane, glider,

helicopter, and multicopter.

(The display screen is an example. The screen

depends on the model type.)

Seven types of main wings (six types of flying

wing) and three types of tail wings are available

for airplanes. Eight swash types are available

for helicopters. Seven types of main wings and

three types of tail wings are available for gliders.

Functions and mixing functions necessary for each

model type are set in advance at the factory.

Note: The Model Type function automatically

selects the appropriate output channels, control

functions, and mixing functions for the chosen

model type.

When the Model Type Selection command is

accessed, all of the data in the active memory is

cleared. Be sure that you don’t mind losing this

data, or back it up to another memory using the

copying functions.

● Select [Model type] at the linkage menu and call

the setup screen shown below.

● When a data change will occur, the confirmation

screen of data initialization menu will be displayed.

A push on [yes] will initialize data and allow changes.
A push on [no] will stop data changes.

Model type selection

1. Model type selection [Model icon], tap.
2. Set the Model type, Wing type(Airplane/

Glider), Tail type(Airplane/Glider), or Swash

type(Helicopter) by using the appropriate

button.

3. Set the type you choose by tapping

[Enter]→[Yes] at the confirmation screen.

(When you want to cancel model type

selection, tap [No].)

●Return to Linkage

1. [Enter], tap

2. [Yes], tap

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды