manualshive.com logo in svg

FUTABA 01000141, Полное руководство

FUTABA 01000141 - полная инструкция пользователя для скачивания бесплатно. Подробный мануал содержит все необходимые сведения о продукте. Скачайте его с manualshive.com прямо сейчас и ознакомьтесь со всеми функциями и возможностями этого устройства.

Поделиться
Скачать
background image

170

＊ Gyro gain channel

Gyro : CH5

For the FASSTest12CH, Gyro/RUD is 6ch. The gyro sensitivity adjustment connector connects to 6ch.

＊ Gyro gain channel

Gyro  RUD : CH5

　

For the FASSTest12CH, Gyro/RUD is 6ch.

Gyro2 AIL : CH9

Gyro3 ELE : CH10　　For the CGY750, simply connect the S.BUS; functions do not need to be set.

                                        (For the FASSTest12CH, change Gyron/RUD to 6ch.)

Usage example #1: Using gyro for only the rudder and adjusting sensitivity for each condition

Usage example #2: Using 3-axis gyro CGY750 and adjusting sensitivity for each condition

Because  sensitivity  changes  for 

hovering  and  idleup,  perform 

switchover for each condition and 

adjust sensitivity.

Because  sensitivity  changes  for 

hovering  and  idleup,  perform 

switchover for each condition and 

adjust sensitivity.

Because the 

sensitivity is switched 

(Sngl) per condition, 

Rate 2 and Rate 3 are 

not used.

Because the 

sensitivity is switched 

(Sngl) per condition, 

Rate 2 and Rate 3 are 

not used.

Tapping here will let 

you select either Normal 

or AVCS for each of the 

three axes.

This is all that is needed 

for use in this case.

This is all that is needed 

for use in this case.

Tapping here will let you 

select either Normal or 

AVCS.

Set gain of a rudder

Set gain of a rudder

Set gain of an aileron

Set gain of an elevator

●  Select  [Gyro]  at  the 

model menu and call 

the setup screen.

●  Select  [Gyro]  at  the 

model menu and call 

the setup screen.

Содержание 01000141


































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 01000141

K&K M8700 Installation Instructions Manual preview
M8700
Бренд: K&K Страницы: 6
BADLANDS LE-03 Quick Manual preview
LE-03
Бренд: BADLANDS Страницы: 2
Fagor CNC 8070 Original Instructions Manual preview
CNC 8070
Бренд: Fagor Страницы: 10
Fagor CNC 8070 Operating Manual preview
CNC 8070
Бренд: Fagor Страницы: 358
Fagor CNC 8070 Programming Manual preview
CNC 8070
Бренд: Fagor Страницы: 556
Fagor CNC 8060 Operating Manual preview
CNC 8060
Бренд: Fagor Страницы: 172
Fagor CNC 8060 Translation Of The Original Manual preview
CNC 8060
Бренд: Fagor Страницы: 180
Fagor CNC 8060 Hardware Configuration preview
CNC 8060
Бренд: Fagor Страницы: 112
FaderMate Master Control Unit Fittings Manual preview
Master Control Unit
Бренд: FaderMate Страницы: 36
Walimex Pro Excellence Instruction Manual preview
Excellence
Бренд: Walimex Pro Страницы: 68
Yealink EXP40 Quick Start Manual preview
EXP40
Бренд: Yealink Страницы: 8
Eaton EZD Series User Manual preview
EZD Series
Бренд: Eaton Страницы: 448
Eaton EC4E-221-6D4T1 Hardware And Engineering preview
EC4E-221-6D4T1
Бренд: Eaton Страницы: 57
ICP DAS USA XP-9 88-IoT Series Quick Start Manual preview
XP-9 88-IoT Series
Бренд: ICP DAS USA Страницы: 8
ICON AIRFLOW PCM Manual preview
AIRFLOW PCM
Бренд: ICON Страницы: 2
ICP DAS USA SP-S2-DS Quick Start preview
SP-S2-DS
Бренд: ICP DAS USA Страницы: 4
Alde 3010 413 Instructions For Use And Assembly preview
3010 413
Бренд: Alde Страницы: 36
PSC Solar YQPV-HP360V/100A Installation And Operating Instructions Manual preview
YQPV-HP360V/100A
Бренд: PSC Solar Страницы: 22

Бренды по названию

Популярные бренды

Загрузить еще бренды