FUTABA 01000141 Скачать руководство пользователя страница 40

Страница: 40 / 225

After setting, press a HOME/EXIT button

After setting

*If there are many FASSTest (T-FHSS) systems

turned on around your receiver, it might not

link to your transmitter. In this case, even if the

receiver's LED stays solid green, unfortunately

the receiver might have established a link

to one of other transmitters. This is very

dangerous if you do not notice this situation.

In order to avoid the problem, we strongly

recommend you to double check whether

your receiver is really under control by your

transmitter by giving the stick input and then

checking the servo response.

*Do not perform the linking operation when

the drive motor is connected or the engine is

running.

10. When a telemetry function is enabled,

the receiving interval (down-link interval)

of sensor data can be changed. If a D/

L interval is increased, the response of the

sensor data display becomes slower, but

stick response will improve.
Initial value: 1.0s

Adjustment range: 0.1s~2.0s

9. ACT will be chosen if telemetry is used.

It is INH when not using it.

*When you use two receivers, please be sure to

setup a "Rx1" and "Rx2" in the "dual" mode.

*Telemetry function cannot be used for the 2nd

receiver.

→

FASSTest18CH

*Telemetry function cannot be used for the dual

receiver.

→

T-FHSS, FASSTest12CH

*You must link one receiver at a time. If both

power supplies to the receivers are switched on

simultaneously, data is received incorrectly by

the transmitter.

*You cannot link three receivers.
*Link is required when a system type is

changed.

*Linking is required whenever a new model is

made.

*FASST MULTI/FASST 7CH cannot be

selected for Europe.

WARNING

After the linking is done, please cycle

receiver power and check that the

receiver to be linked is really under the

control of the transmitter.

Do not perform the linking procedure

with motor's main wire connected or

with the engine operating as it may

result in serious injury.

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды