FUTABA 01000141 Скачать руководство пользователя страница 33

Страница: 33 / 225

Receiver's Antenna Installation

The R7108SB has two antennas. In order to maximize signal reception and promote safe modeling Futaba

has adopted a diversity antenna system. This allows the receiver to obtain RF signals on both antennas and

fly problem-free.

To obtain the best results of the diversity function,

please refer to the following instructions:

1. The two antennas must be kept as straight as

possible. Otherwise it will reduce the effective

range.

2. The two antennas should be placed at 90

degrees to each other.

This is not a critical figure, but the most

important thing is to keep the antennas

away from each other as much as possible.

Larger models can have large metal objects

that can attenuate the RF signal. In this case

the antennas should be placed at both

sides of the model. Then the best RF signal

condition is obtained at any flying attitude.

3. The antennas must be kept away from

conductive materials, such as metal, carbon

and fuel tank by at least a half inch. The

coaxial part of the antennas does not need

to follow these guidelines, but do not bend it

in a tight radius.

4. Keep the antennas away from the motor,

ESC, and other noise sources as much as

possible.

Antenna

*Must be kept as straight as possible.

Coaxial cable

R7108SB Receiver

Sleeve

Antenna

installation

90°

Do not bend the antenna part

Gently bend the coaxial

cable part.

Fix the sleeve to the model

Antenna part

Sleeve

Coaxial cable

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды