FUTABA 01000141 Скачать руководство пользователя страница 201

Страница: 201 / 225

201

The dedicated mixes, etc. usable when

multicopter model type is selected are displayed

in this Model menu functions section.

These dedicated mixes can be set for each

flight condition, as required. When you want to

use the system by switching the settings for each

condition by switch or stick position, use the

Condition select function to add flight conditions.

(Up to 8 conditions can be used)

MODEL MENU (Multicopter functions)

Model menu (Multicopter) functions table

Servo monitor

Displays the servo test and operation position

Condition select

Flight conditions addition, deletion, copy, condition renaming, and condition delay can be set.

AFR

Sets the angle and curve of all the operation functions.

Dual rate

D/R curve which can be switched with a switch, etc. can also be added.

Program. mixes

Program mixing which can be freely customized. Up to 10 mixes can be used for each condition.

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды