FUTABA 01000141 Скачать руководство пользователя страница 89

Страница: 89 / 225

Registered sensor

Slot Number

This is what displays when no

sensor is registered in a slot.

Tapping the slot and selecting

"-----------" will erase whatever was

registered there, freeing up the

slot.

Tap the slot to display

sensors which can be used

for the start slot. Tap to

register the sensor.

Sensor ID : Multiple usage of sensors

of the same type requires an ID

be input. Tapping this will allow

for manual input, but see the next

page about how to perform auto-

registration via sensor registration.

Sensor

Various telemetry sensors setting

This screen registers the telemetry sensors used

with the transmitter. When only one of a certain

type of sensor is used, this setting is unnecessary

and the sensor can be used by simply connecting it

to the S.BUS2 port of the transmitter.

When using 2 or more of the same kind of sensor,

they must be registered here.

[What is a slot?]

Servos are classified by CH, but sensors are

classified in units called “slot”. There are slots from

No. 1 to No. 31.

Altitude sensors, GPS sensors and other data

sensor units may use multiple slots.

When using a sensor which uses two or more

slots, the required number of slots is automatically

assigned by setting up a start slot.

When 2 or more of the same kind of sensor are

used, the sensors themselves must allocate unused

slots and memorize that slot.

● As shown in the table below, an altimeter requires 3 contiguous slots and a GPS sensor

requires 8 contiguous slots. The GPS (SBS-01/02G) start slots are 8, 16, and 24.

＜

Assignable slot

＞

*Altimeter, GPS, and other sensors that display a large amount of data require multiple slots.

*Depending on the type of sensor, the slot numbers that can be allocated may be limited.

● Tap the [Sensor] button in the Linkage menu

to call the setup screen shown below.

Sensor

The required number

of slots

The number which can be used as a start slot

Selling area

TEMP (SBS-01T/TE)

1 slot

Global

RPM (SBS-01RM/RO/RB)

1 slot

Airspeed (SBS-01TAS)

1 slot

Voltage (SBS-01V)

2 slots

1 , 2 , 3 , 4 , 5 , 6 , 8 , 9 , 1 0 , 1 1 , 1 2 , 1 3 , 1 4 , 1 6 , 1 7 , 1 8 , 1 9 ,

2 0 , 2 1 , 2 2 , 2 4 , 2 5 , 2 6 , 2 7 , 2 8 , 2 9 , 3 0

Altitude (SBS-01/02A)

3 slots

1 , 2 , 3 , 4 , 5 , 8 , 9 , 1 0 , 1 1 , 1 2 , 1 3 , 1 6 , 1 7 , 1 8 , 1 9 , 2 0 , 2 1 ,

2 4 , 2 5 , 2 6 , 2 7 , 2 8 , 2 9

Current (SBS-01C)

3 slots

1 , 2 , 3 , 4 , 5 , 8 , 9 , 1 0 , 1 1 , 1 2 , 1 3 , 1 6 , 1 7 , 1 8 , 1 9 , 2 0 , 2 1 ,

2 4 , 2 5 , 2 6 , 2 7 , 2 8 , 2 9

S.BUS Servo sennsor

（

SBS-

01S)

6 slots

1 , 2 , 8 , 9 , 1 0 , 1 6 , 1 7 , 1 8 ,

2 4 , 2 5 , 2 6

GPS(SBS-01/02G)

8 slots

8 , 1 6 , 2 4

EM-100 (O.S. ENGINE)

12 slots

8 , 1 6

TEMP125-F1713

1 slot

Europe

VARIO-F1712

2 slots

1 , 2 , 3 , 4 , 5 , 6 , 8 , 9 , 1 0 , 1 1 , 1 2 , 1 3 , 1 4 , 1 6 , 1 7 , 1 8 , 1 9 ,

2 0 , 2 1 , 2 2 , 2 4 , 2 5 , 2 6 , 2 7 , 2 8 , 2 9 , 3 0

VARIO-F1672

2 slots

1 , 2 , 3 , 4 , 5 , 6 , 8 , 9 , 1 0 , 1 1 , 1 2 , 1 3 , 1 4 , 1 6 , 1 7 , 1 8 , 1 9 ,

2 0 , 2 1 , 2 2 , 2 4 , 2 5 , 2 6 , 2 7 , 2 8 , 2 9 , 3 0

CURR-F1678

3 slots

1 , 2 , 3 , 4 , 5 , 8 , 9 , 1 0 , 1 1 , 1 2 , 1 3 , 1 6 , 1 7 , 1 8 , 1 9 , 2 0 , 2 1 ,

2 4 , 2 5 , 2 6 , 2 7 , 2 8 , 2 9

GPS-F1675

8 slots

8 , 1 6 , 2 4

Kontronik ESC

8 slots

8 , 1 6 , 2 4

Castle TL0

8 slots

8 , 1 6 , 2 4

JetCat V10

14 slots

1 , 2 , 3 , 4 , 5 , 6 , 7 , 8 , 9 , 1 0 , 1 1 , 1 2 , 1 3 , 1 4 , 1 5 , 1 6 , 1 7 ,

1 8

PowerBox

16 slots

8 , 1 6

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды