FUTABA 01000141 Скачать руководство пользователя страница 98

Страница: 98 / 225

Variometer

Sets the variometer

on which the alarm

operates.

↑ An upward arrow

indicates the alarm

will sound when the

variometer reaches

above your set value.

↓ A downward arrow

indicates the alarm

will sound when the

variometer reaches

below your set value.

Alarm is chosen from

Buzzer, Voice, and

Inhibit.

Allows Speech to be

turned ON or OFF.

Allows Melody to be

turned ON or OFF.

● Tap the [Variometer] button in the Telemetry screen

to call the setup screen shown below.

Max. and min. values

s i n c e t h e p o w e r

was turned ON will

display.

*It cannot be used in FASST mode and S-FHSS mode.

*Only receiver voltage and EXT voltage can be used in

FASSTest12CH mode.

*The FASSTest18CH /T-FHSS mode can use all the telemetry

functions.

Type 1

Type 2

Type 3

"Vibrator" type

If the following types are selected, the transmitter

will vibrate during the warning.

First, the set of a reference is required.

1. The model and transmitter to which the

altitude sensor was connected are turned on.

2. Tap to the [Preset] of "Reference" item.

*Atmospheric pressure is changed according to the weather

also at the same airfield. You should preset before a flight.

*An altitude sensor or GPS sensor must be installed in the aircraft.

Telemetry : Altitude [Variometer]

Displaying data from the

variometer

VARIO is a screen which displays / sets up the

variometer information from an optional altitude

sensor or GPS sensor.

The variometer of the model which is flying can be

known.

If it becomes higher or lower than the setting, an

alarm and/or vibration will alert you.

To ensure that the pilot is aware as to the model's

status, the T16IZ incorporates a different melody

for ascent and descent. Additionally, depending

upon the rate of climb or descent, the tones vary to

indicate whether or not the airplane is climbing or

descending at a rapid rate.

Alert set : variometer

1. Tap Alarm and choose from Buzzer, Voice,

and Inhibit.

2. Choose "Inhibit" for Vibrator if no

using the

vibrator alarm. If using vibrator, choose one

of the three types.

3. Tap to the Limit [m/s] item .

4. Adjust the rate using the "▼▼" "▼" "▲" "▲▲"

buttons.

Initial value: +1m

Adjustment range-50 m/s~+50 m/s

(↑Limit

≧

↓Limit)

*When the screen is tapped for one second, the rate is reset

to the initial value.

5. To terminate the input and return to the

original state, push the HOME/EXIT button.

● If this is set to Mode1-4,

a rise and dive are told

by a different melody.
Mode 1 : Little rise/dive

→ Melody changes

: sensitively

Mode 4 : Big rise/dive

→ Melody changes

: insensible

●Return to

Linkage menu

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды