FUTABA 01000141 Скачать руководство пользователя страница 122

Страница: 122 / 225

122

AFR

The angle and curve of each operation function can be set. [All model types]

AFR function is used to adjust the throw and

operation curve of the stick, lever, and switch

functions for each flight condition.

This is normally used after End Point has defined

the maximum throw. When mixing is applied from

one channel to another channel, both channels

can be adjusted at the same time by adjusting the

operation rate through the AFR function.

● Operation curve adjustment: Three types

of curves (EXP1, EXP2, and Point) can be

selected. A maximum 17 points curve can be

used for the point curve type. (Initial setting:

9 points) The number of points can also be

increased and decreased and curves from

complex curves to simple curves can be

used.

● Operation speed adjustment: The operation

speed of each function when the function

is operated (including at flight condition

switching) can be adjusted. The function

operates smoothly at a constant speed

corresponding to the set speed.

● Select [AFR] at the model menu and call

the setup screen shown below.

Function selection

1. When the function select button is tapped, a selection screen appears.
2. Select the function you want to set at the selection screen.

When D/R is turned ON, the display will

show "D/R----", and the rudder angle (rate)

and EXP can be set when D/R is ON.

● Operation curve setting

(For a description of the setting method, see the

description at the back of this manual.)

● Servo speed setting

(For a description of the setting

method, see the description at

the back of this manual.)

● Group/single mode switch (Gr./Sngl)

(For more information, see the

description at the back of this manual.)

●Return to Model menu

Left/right, Up/down, overall

adjustment at Rate A and

Rate B

Curve select

Separately ⇔ Combination

(Left and right

symmetrical

curve.)

Curve select

EXP1, EXP2, Point curve

100%

40%

Rate

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды