FUTABA 01000141 Скачать руководство пользователя страница 160

Страница: 160 / 225

160

Pitch trim (Hovering pitch, high pitch, low pitch)

The hovering pitch, low pitch, and high pitch trim setup screen can be called from the Pitch curve setup

screen.

Hovering pitch trim

setting

Low/high pitch trim

setting

Hovering pitch trim

The Hovering Pitch trim function trims the pitch

near the hovering point. Normally, it is used with

the hovering condition. The hovering pitch can be

fine tuned for changes in rotor speed accompanying

changes in temperature, humidity, and other flight

conditions. Adjust the hovering pitch so that

rotor speed is constant. This function can be used

together with the hovering Throttle Trim function

for more delicate operation.

Setting method

● When using only the hovering (normal)

condition, switch the group mode to the

single mode (initial setting) before setting.

● Tap [INH]. (ON is displayed.)
● Select the adjustment knob.

Selection example: LD

● The trim operation mode (Mode: Center/

Normal) can be selected.

Center mode: Maximum amount of change

near center by center trim operation

(recommended)

Normal mode: Normal trim (parallel

movement trim) operation. The advantage

of using this mode is that the hovering pitch

can be adjusted without changing the

curve.

● Trim adjustment range (Range) setting

When this value is made small, trim can only

be used near the center.

● The trim rate can be adjusted and the

operation direction can be changed.

High Pitch/Low Pitch Trim

High Pitch/Low Pitch Trim is the pitch servo high

side and low side trim function.

Setting method

● When setting the adjustment knobs common

to all the conditions, set them in the group

mode.

● Tap [INH]. (ON is displayed.)
● Select the adjustment knobs.

Selection example: LS (high side), RS (low

side)

● The trim rate can be adjusted and the

operation direction can be changed.

● Trim acts as high side or low side trim with the

center as the standard.

●Return to Model menu

Содержание 01000141


































































































































































































































Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды

FUTABA 01000141, Полное руководство

Результаты поиска

Содержание 01000141

Отзывы:

Похожие инструкции для 01000141

Бренды по названию

Популярные бренды