FUTABA 01000141 Скачать руководство пользователя страница 221 | Manualshive

Страница: 221 / 225

background image

221

Updating

Your Futaba T16IZ transmitter programming can be updated easily online. When functions

are added or improved, the update file can be downloaded from our website. Copy the

update files to the SD card and then use the following procedure to update the program.
Check our web site for the FAQ regarding updating for more information.

Updating procedure

Note: If the battery fully discharges during

program updating, updating will fail. When

the remaining battery capacity is 50% or

less, always recharge the battery before

updating.

Note: The model data in the transmitter can

be used unchanged after updating, but to

be safe, back up the model data before

updating.

1. Download the zip file of the update data

from our website.

2. Extract the zip file on your computer.

3. The "FUTABA" folder will be created on your

computer.

4. Copy the "FUTABA" folder into your SD card.

Note: If the SD card has already had "another

FUTABA" folder before you make a copy, the

"FUTABA" folder is OVERWRITTEN.

5. Insert the SD card with "FUTABA" folder that

contained the update software into the SD

card slot on your T16IZ radio transmitter.

6. Turn on the transmitter power while pressing

down the "HOME/EXIT" button. The update

screen appears on the LCD display of your

T16IZ and the software update is started.

Futaba WEB

16IZ Update Zip ﬁle

Download

Copy the "FUTABA"

folder into your SD card.

Installed SD card of the

update file

Press the HOME/EXIT switch and turn on

Updating

1

2

«
...
219
220
221
222
223
...
»

Содержание 01000141


































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 01000141

Бренд: Access Страницы: 12

Бренд: Jetline Страницы: 58

Бренд: Eaton Страницы: 288

Tissue-Tek TEC 6

Бренд: Sakura Seiki Страницы: 6

Бренд: Parker Страницы: 54

Бренд: RAM Страницы: 71

Бренд: Voltech Страницы: 8

Бренд: Baier Страницы: 20

Бренд: Nice Страницы: 32

Бренд: Velux Страницы: 11

Бренд: Kantronics Страницы: 201

Бренд: SILENTRON Страницы: 20

Бренд: MacroAir Technologies Страницы: 32

Бренд: Anthem Страницы: 8

Бренд: National Instruments Страницы: 11

Airedale Sentinel

Бренд: Modine Manufacturing Страницы: 2

Бренд: Waterbird Страницы: 19

MOBA-Matic MMC-1000

Бренд: MOBA Страницы: 172

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды